OPERATING INSTRUCTIONS
Indicating lamp
Main power switch
Turning Power On and Off
•To turn the monitor power ON, press the main power switch on the monitor main unit to ON, and then press the SUB POWER button or the ON/OFF or ON button on the remote control.
•To turn the monitor power OFF, press the SUB POWER button or the ON/OFF or OFF button on the remote control, and then press the main power switch on the monitor main unit to OFF.
•During normal use, the main power switch is set in the ON position, and the monitor can then be turned ON/OFF using the SUB POWER button or the ON/OFF button on the remote control.
|
|
|
|
|
|
|
|
| Indicating lamp |
| |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Indicating | Power status | Operating |
|
|
|
|
|
|
|
|
| lamp | ||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Off | Off | When the main power switch is set |
|
|
|
|
|
|
|
|
| to OFF. | ||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| When the main power switch is |
|
|
|
|
|
|
|
|
|
| Off | ON, and the OFF button on the |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| Lights red | remote control or the SUB POWER | |
|
|
|
|
|
|
|
|
| (standby) | ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| button on the underside of the | |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| front of the frame is OFF. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| When the main power switch is |
|
|
|
|
|
|
|
|
|
|
| ON, and the ON button on the |
|
|
|
|
|
|
|
|
| Lights green | On | remote control or the SUB POWER |
|
|
|
|
|
|
|
|
|
|
| button on the underside of the |
|
|
|
|
|
|
|
|
|
|
| front of the frame is ON. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| When the main power switch is |
|
| ON, and the ON button on the | |||||||||
|
|
|
|
|
|
|
|
|
| Off | remote control or the SUB POWER |
|
|
|
|
|
|
|
|
| Lights orange | button on the underside of the | |
|
|
|
|
|
|
|
|
| (Power Save) | ||
|
|
|
|
|
|
|
|
|
| front of the frame is ON. | |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| However, the state in POWER |
|
|
|
|
|
|
|
|
|
|
| SAVE mode |
|
|
|
|
|
|
|
|
|
|
|
|
POWER OFF |
| |
button |
| |
POWER ON | POWER ON/OFF | |
button | ||
button | ||
| ||
| VOL | |
| RGB 1 RGB 2 MUTE VOL |
AV1 AV2 AV3 AV4
AUTO PinP SIZE RECALL
MENU
When the indicating lamp lights in orange or the message “No Sync. Signal”, “Power Save” or “Invalid Scan Freq.” appears on the screen, there is something unusual about the status of reception.
See “Power Save Mode” or “Symptoms That Seemingly Appear to be Failures.” 
ATTENTION
•Avoid repeatedly turning the monitor on and off at short time intervals. Failures might result from such operation.
•Turn off the main power switch before leaving the monitor out of use for an extended period of time.
•If a power failure occurs while the main unit is running, it would be powered on upon recovery from the failure. Turn off the unit main power switch before leaving the main unit.
OK
ID | ID SET |
16
