Manuals / Hitachi / Computer Equipment / Projector

Hitachi CP-X955E Control data table, Connection to the control signal terminal continued

Models: CP-X955E

1 30

Download 30 pages 43.67 Kb

Page 25

Control data table

Connection to the control signal terminal (continued)

				Control data table
Item	Data code

MOUSE	00h=stop mouse emulation. 01 ∼ 7Fh=start mouse emulation

COMMUNICATE	0Xh=8N1
	1Xh=7N1
	X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps

POWER	1Eh=Power off (Standby mode), 1Fh=Power on

ZOOM	01-3Fh=Zoom +, 41-7Fh=Zoom- 01, 04 (up) ∼ 3F, 7F (down)

FOCUS	01-3Fh=Focus +, 41-7Fh=Focus- 01, 04 (short) ∼ 3F, 7F (long)

MIRROR	00h=Normal, 01h=H:Invert, 02h=V:Invert, 03h=H & V:Invert

INPUT	11h=VIDEO1, 12h=VIDEO2, 21h=RGB1, 22h=RGB2

VIDEO SYSTEM	00h	00h=Auto, 00h 01h=NTSC, 00h 04h=NTSC4.43
	00h	02h=PAL, 00h 03h=SECAM, 00h 05h=M-PAL

VOLUME	00h (min) ∼ 7Fh (max)

MUTE	00h=Mute off, 01h=Mute on

BRIGHT	00h	00h	00h	(dark) ∼ 00h 00h 7Fh (brite)

CONTRAST	00h	00h	00h	(lower) ∼ 00h 00h 7Fh (higher)

COLOR	00h	00h	20h	(less) ∼ 00h 00h 60h (more)

TINT	00h	00h	2Eh (red) ∼ 00h 00h 52h (green)

SHARPNESS	00h	00h	00h	(soft) ∼ 00h 00h 64h (sharp)

H.PHASE	00h	00h	00h ∼ 00h 00h 1Fh

H.POSIT	00h	00h	52h	00h (left) ∼ 00h	00h 54h 04h (right)

H.SIZE	00h	00h	00h	06h (narrow) ∼ 00h 00h 48h 0Bh (wide)

V.POSIT	00h	00h	06h	00h (down) ∼ 00h 00h 50h 05h (up)

BLANK	0Xh=Blank off
	1Xh=Blank on
	bit0 0=Blue off, 1=Blue on,				bit1 0=Green off,	1=Green on
	bit2 0=Red off, 1=Red on,				bit3 0=Not change,	1=Change

REVEAL	X1h=Reveal down, X4h=Reveal right, X=0 (slow) ∼ 7 (fast)

Caution If computer sends the undefined command code or data code, Projector can not guarantee operation.

Command is consisted of 2 command bytes and following data bytes. 1-st byte indicates the kinds of commands and the length of command.

‘0xH’ : Error-reply	Projector sends to computer.
‘1xH’ : Command reply	Projector sends to computer.
‘2xH’ : Ask command	Computer sends to Projector.
‘3xH’ : Set command	Computer sends to Projector.
‘4xH’ : Default set command	Computer sends to Projector.

‘5xH’ — ‘FxH’ : Reserved

‘x’ indicates the length of data bytes.

2-nd byte indicates the command code ‘yy’ as command table. Data table shows the data byte.

25

Downloaded from www.Manualslib.com manuals search engine

Image 25

Hitachi CP-X955E Control data table, Connection to the control signal terminal continued, Projector sends to computer

Contents

ContentsPage Features2 High resolution 3 Compact size, light weight for portability 4 RGB output terminalWARNING THIS EQUIPMENT MUST BE EARTHED IMPORTANT FOR THE CUSTOMERS IN U.KIMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS2 Power cord 1 Video signal cablesBefore use Warning CautionL Do not look directly at the lens when the lamp is lit Safety precautionLDo not install this unit in an unstable L Do not use power supplies other than that specifiedL Do not stare directly into the laser aperture L Be careful in handling the power cordC A U T I O N L Handle the power cord carefully L CleaningL Clean inside the unit at least once two years L When you are not going to use for a long timeL Volume L Do not place this unit where it gets hotL Cleaning the lens L Cleaning the cabinetMain unit Names and functions of each partNames and functions of each part continued Remote control transmitterª Insert the batteries as illustrated inside the battery compartment Á Remove the battery compartment coverCaution Cautions on use of batteries £ Replace the cover Caution Cautions on useExample of the projector and screen installation InstallationHow to use foot adjusters Installation of liquid crystal projectorBasic operations 1 Turn the MAIN POWER switch of the projector on. I ONTo project the picture +++FOCUS+++Turn the MAIN POWER switch of the projector off. ª OFF To turn off the powerBasic operations continued PLUG & PLAYTo return to the initial setting Adjustments and functionsMemory function 1 Press the MENU buttons or the MENU ON / OFF buttonSET UP Adjustments and functions continuedIMAGE INPUTAdjustments and functions continued The menu INPUT serves for the selection of input sourceAdjustments and functions continued OPT. OPTIONThe menu OPT. allows you to control communication function etc COM. SPEED Adjustments and functions continuedCOM. BITS LANGUAGEConnection to the RGB signal terminal Connection to the video signal terminals1. Input signal 2. Signal input terminal3. Example of computer signal Connection to the RGB signal terminal continued4. Initial set signals Connection to the RGB signal terminal continuedDATA HSYNC DATA VSYNC1. Control signal terminal Connection to the control signal terminal2. Mouse emulation PS/2 mouse ADB Mac mouse Serial mouse Connection to the control signal terminal continued4. Control command code Connection to the control signal terminal continuedControl command table 3. CommunicationConnection to the control signal terminal continued Control data tableProjector sends to computer Projector sends to computerThe procedure of setting the Projector status The procedure of getting the Projector statusThe procedure of default setting the Projector status The example of command errorCleaning the air filter Example of system setupConnecting various equipment 2 Remove the air filter from the bottom3 Clean the air filter using a vacuum cleaner Cleaning the air filter continued4 Re-install the air filter LampIndicator display When you think something wrongCheck the following again before asking for service If the trouble cannot be recovered, consult your dealerAll dimensions shown in inches Dimension diagram