When driving machine screws Fig | Hitachi DH 24PC2 guide

English

◯Drill bit may snap off while withdrawing the rotary hammer from the drilled hole. For withdrawing, it is important to use a pushing motion.

◯Do not attempt to drill anchor holes or holes in concrete with the main unit in the rotation only function.

◯Do not attempt to use the rotary hammer in the rotation and striking function with the drill chuck and chuck adaptor attached. This would seriously shorten the service life of every components of the machine.

4.When driving machine screws (Fig. 11)

First, insert the bit into the socket in the end of chuck adaptor (D).

Next, mount chuck adaptor (D) on the main unit using procedures described in 5 (1), (2), (3), put the tip of the bit in the slots in the head of the screw, grasp the main unit and tighten the screw.

Bit

Socket

Chuck Adaptor (D)	Front Cap
Chuck Adaptor (D)
	Grip

Fig. 11

CAUTION:

◯Exercise care not to excessively prolong driving time, otherwise, the screws may be damaged by excessive force.

◯Apply the rotary hammer perpendicularly to the screw head when driving a screw; otherwise, the screw head or bit will be damaged, or driving force will not be fully transferred to the screw.

◯Do not attempt to use the rotary hammer in the rotation and striking function with chuck adaptor (D) and bit attached.

5.When driving wood screws (Fig. 11)

(1) Selecting a suitable driver bit

Employ phillips screws, if possible, since the driver bit easily slips off the heads of slotted-head screws.

(2) Driving in wood screws

◯ Prior to driving in wood screws, make pilot holes suitable for them in the wooden board. Apply the bit to the screw head grooves and gently drive the screws into the holes.

◯ After rotating the rotary hammer at low speed for a while until a wood screw in partly driven into the wood, squeeze the trigger more strongly to obtain the optimum driving force.

CAUTION:

◯Exercise care in preparing a pilot hole suitable for the wood screw taking the hardness of the wood into consideration. Should the hole be excessively small or shallow, requiring much power to drive the screw into it, the thread of the wood screw may sometimes be damaged.

14

Image 14

Hitachi DH 24PC2 instruction manual When driving machine screws Fig, When driving wood screws Fig

Contents

Manual DE Instrucciones E Instrucciones DE Seguridad Rotary Hammer Marteau rotatif Martillo perforador Contents Meanings of Signal Words Safety English Never operate without all guards in place Blades and accessories must be securely mounted to the toolNever touch moving parts Use right tool Never use a tool which is defective or operating abnormally Keep motor air vent cleanOperate power tools at the rated voltage Do not wipe plastic parts with solvent Make Them Available to Other Users Owners of this Tool Name of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Confirming condition of the environment Mounting the drill bit Fig Selecting the driver bit HOW to USESwitch operation Confirm the direction of bit rotation Fig Rotation + Hammering Rotation only When driving machine screws Fig When driving wood screws Fig Using depth gauge Fig Hammering only On the rests. Fig HOW to USE the Core BIT for Light LoadMounting How to bore Fig Dismounting. Fig Maintenance and Inspection Sold separately AccessoriesStandard Accessories Drill Bit Taper shank and taper shank adaptor Inner wedge type with the headless screw Knock-in anchor Rotation + HammeringOuter wedge type with the female screw Outer wedge type with Female screw Large hole boring Rotation + Hammering Guide plate English Dust cup, Dust collector B Drilling holes rotation onlyPhillips Driver Bit Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENT Conserver CES Instructions SecuriteRegles Generale DE Securite Avertissement Lire et coxmprendre toutes les instructions Français Utiliser l’outil correct Regles DE Securite Specifiques ET SymbolesNE Jamais toucher les parties mobiles Utiliser l’outil motorisé à la tension nominale Manipuler l’outil correctementGarder propres les évents d’air du moteur Ne pas essuyer les parties en plastique avec du solvant 22. Définitions pour les symboles utilisés sur cet outil Double Isolation Pour UN Fonctionnement Plus SUR 4600/min Poids Lbs 2,5 kg Description FonctionnelleNOM DES Parties Avant L’UTILISATION Avertissement Vérification des conditions d’environnement Montage du foret de perçage Fig Vérifiez la direction de rotation de La mèche Fig UtilisationSélection de la mèche pour visseuse Fonctionnement de l’interrupteur Rotation + percussion Rotation seulement Lors du vissage des vis machine Fig Enfoncement de vis à bois Fig Percussion uniquement Utilisation de la quenouille Fig Conique et le raccord de queue Comment Utiliser LA Couronne Pour UNE Charge LegereComment utiliser la mèche queue Conique Perçage Fig Démontage Fig Entretien ET Inspection Vendus séparément AccessoiresAccessoires Standard Foret de perçage queue conique et raccord de queue conique Cône en a 303619 Type à cale intérieure avec vis sans tête Ancrage de chasse Rotation + percussionType à cale extérieure avec vis femelle Perçage de trou à large diamètre Rotation + percussion Plaque centrale de guidage Français Capuchon anti poussière, Collecteur à poussière B Perçage de trous rotation seulementEmbout de vissage Phillips Información Importante Sobre Seguridad Significado DE LAS Palabras DE Señalización Guarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Advertencia Lea y entienda todas las instrucciones Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles No limpie las partes de plástico con disolvente Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas Amperios VoltiosHertzios Velocidad sin carga Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura 4600/min Peso Lbs 2,5 kg Antes DE LA Operación Montaje Y OperaciónAplicaciones Advertencia Confirme las condiciones del medio ambiente Montaje de la broca Fig Confirmar la dirección de rotación de la broca Fig Como SE USASelección de la broca destornillador Operación del conmutador Rotación + golpeteo Rotación solamente Cuando coloque tornillos para metal Fig Atornillando tornillos para madera Fig Golpeteo solamente Modo de usar el tope Fig Modo DE Usar LA Barrena Tubular Para Cargas Ligeras Montaje Modo de taladrar Fig Desmontaje Fig Mantenimiento E Inspección Broca de taladro vástago cónico y adaptador cónico AccesoriosAccesorios Estándar Ancla de martillar Rotación + golpeteo Tipo de reborde exterior con tornillo hembra Tipo de reborde interior con tornillo sin cabeza Placa guia     Copa de polvo, Colector de polvo B Perforación rotación solamenteBroca para tornillos Plillips Page 501 502 503 CDA B CD Page Page Kestrel Road Mississauga on L5T 1Z5