Hitachi L32A104 important safety instructions TV operation, To select the video input source

Press ▲ or ▼ to select “TV Location”, then press ◀ or ▶ to select “Home” or “Store”.

This unit has been preset to STORE brightness This setting does not qualify under ENERGY STAR. To reduce brightness and energy consumption, change setting to ‘HOME’. This setting does qualify under ENERGY STAR.

Scan

Start

Source

Cable

TV Location

Store

Starting setup

The Auto Setup menu appears the first time you turn on the TV. It will assist you to specify the Air/Cable setting and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

1 To turn on the TV, press POWER (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.

Auto Setup

2

: Move : Adjust

TO SELECT DIGITAL CHANNELS
Press the first 1-3 digits, then press the – button followed by
the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1, then press
ENTER.
•	If a channel is selected with only audio content, “Audio only”
•	will be displayed on the screen.
	If a channel is selected with a weak digital signal, “Weak
	Signal or Channel not available” will be displayed on the
•	screen.
	The same program may be available on either an analog
	channel or a digital channel.You may choose to watch			ENGLISH
•	either format.
	If a channel is selected to which you have not subscribed,
	“Digital channel is encrypted” will be displayed on the
	screen.
VHF/UHF/CABLE CHANNELS
	Air		Cable
VHF			VHF
2-13			2-13
UHF		STD/HRC/IRC
14-69		14-36	(A) (W)

NOTE:

• This unit has been preset to STORE brightness. This setting does not qualify under ENERGY STAR. To reduce brightness and energy consumption, change setting to ‘HOME’. This setting does qualify under ENERGY STAR.

• The device may not conform to the ENERGY STAR standard after Reset is performed or the Backlight is adjusted.

3 Press ▲ or ▼ to select “Source”, then press ◀ or ▶ to select “Cable” or “Air”.

4 Press ▲ or ▼ to select “Scan”, then press ▶ or ENTER.

5 “Auto Setup” will begin. After the Auto Setup is completed, the TV channel appears on the screen.

• Depending on the reception condition, it may take up to 25 minutes or more to complete memorizing digital cable channels. Please allow the process to complete without interruption.

NOTE:

• If you press ENTER in the process of “Auto Setup”, the Auto Setup stops and changes to the normal screen.

• When you make a menu selection, your changes occur immediately.You do not have to press EXIT to see your changes.

TV operation

1 To turn on the TV, press POWER.

(POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.)

2 Adjust the volume level by pressing VOL + or – . The volume

level will be indicated on the screen by blue bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of blue bars also decreases.

3 Set the Source option to the appropriate position (see “Air/ Cable selection” on page 20).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only the channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

37-59	(AA) (WW)
60-85	(AAA) (ZZZ)
86-94	(86) (94)
95-99	(A-5) (A-1)
100-135	(100) (135)
01	(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT, then press ▲ or ▼ or the corresponding Number buttons (0-6), then press ENTER.You can select TV, Video1, Video2, Component, HDMI1, HDMI2 or PC depending on which input jacks you used to connect your devices.

Input List

0.TV

1.Video1

2.Video2

3.Component

4.HDMI1

5.HDMI2

6.PC

[0-6]:Select

CH /

Press and release CH /. The channel automatically stops at the next channel set into memory.

For proper operation, before selecting channels, they should be set into the memory. See “Memorizing channels” on page 20.

17