Memorizing channels

This TV is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the TV’s memory. To use this TV with an antenna, set the Source option to the Air mode. When shipped from the factory this menu option is in the Cable mode.

Air/Cable selection

1 Select “Channel”, then press or ENTER.

2 Press ▲ or ▼ to select “Auto Channel Scan”, then press or

ENTER.

3 Press ▲ or ▼ to select “Source”.

4 Press or to select “Air” or “Cable”.

Air - VHF/UHF channels

Cable - CABLE TV channels

CH Auto Channel Scan

SourceCable

ScanStart

:Move :Adjust

NOTE:

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

Scan

1 Select “Channel”, then press or ENTER.

2 Press ▲ or ▼ to select “Auto Channel Scan”, then press or

ENTER.

3 Press ▲ or ▼ to select “Scan”, then press or ENTER.

CH Auto Channel Scan

Source

Cable

Scan

Cancel

Analog Channel Found : 7

Digital Channel Found : 5

Scanning

:Move

ENTER :Cancel

4 The TV will begin memorizing all the channels available in your area.

• It may take from 15 minutes to 25 minutes to complete memorizing digital cable channels.

• Depending on the reception condition, a bar display may not advance for several minutes, please be patient.

NOTE:

Memorizing channels is best accomplished during evening “PRIMETIME” hours, as more stations are broadcasting digital signals. Memorizing channels can only be accomplished while a station is broadcasting a digital signal to set that channel into memory.

If you are unsure of the digital channels available in your area, you may visit www.antennaweb.org to receive a list based on your address or zip code. Should you require further assistance you may call our toll-free customer service line at 1-800-289-0981 (USA/CANADA).

New digital channels may be added to your area periodically, it is recommended to perform the “Scan” procedure regularly.

Add Digital Channel

If you find a new unregistered digital channel, you can add the new channel into the channel memory.

1 Tune in the new channel.

2 Select “Channel”, then press or ENTER.

3 Press ▲ or ▼ to select “Channel Manager”, then press or

ENTER.

CH Channel Manager

Add Digital Channel

>>

View/Skip

>>

Clear All

>>

:Move

ENTER :Select

4 Press ▲ or ▼ to select “Add Digital Channel”, then press or ENTER. The new channel will be added into the channel memory.

View/Skip channel

You can select the channel that you want to skip.

1 Select “Channel”, then press or ENTER.

2 Press ▲ or ▼ to select “Channel Manager”, then press or

ENTER.

3 Press ▲ or ▼ to select “View/Skip”, then press or ENTER. 4 Press ▲ or ▼ to select the channel that you want to skip.

CH View/Skip

CH

Signal

 

2

Analog

Skip

3

Analog

View

3-1

Digital

View

3-2

Digital

View

4

Analog

View

:Move :Adjust

5 Pressor to select “View” or “Skip”, whichever function you want to perform.

6 Repeat steps 4 - 5 for other channels you want to view or skip.

Clear All

All channels are deleted from the channel memory.

1 Select “Channel”, then press or ENTER.

2 Press ▲ or ▼ to select “Channel Manager”, then press or

ENTER.

3 Press ▲ or ▼ to select “Clear All”, then press or ENTER.

CH Channel Manager

Add Digital Channel

>>

View/Skip

>>

Clear All

>>

:Move

ENTER :Select

16

Page 16
Image 16
Hitachi L40A105A important safety instructions Memorizing channels