Hitachi SJ100 manual Display Function Standard Set Setting Value, From previous

Display		Function		Standard	Set
				Setting	Value
A	01	Frequency Source setting		01
		00-Potentiometer 01-Terminal O/OI
		02-Functions F 01 / A 20
A	02	Run command source setting		01
		01-Terminal FW/RV	02-RUN key
A	03	Base frequency setting		50.0
A203		Base frequency setting (2. setting)
A	04	Maximum frequency setting		50.0
A204		Maximum frequency setting (2. setting)
A	11	External frequency setting start point		0
A	12	External frequency setting end point		0
A	13	External frequency setting start point bias (in %)		0
A	14	External frequency setting end point bias (in %)		100
A	15	External frequency start pattern setting		01
		00-Per A11 and A13	01-0Hz
A	16	Time constant of the filter for analog inputs		8
A	20 –	Multispeed frequency setting		All are
A	35			0.0Hz
A	38	Jog frequency setting		1.0
A	39	Jog stop mode		00
		00-Freerun 01-Deceleration
		02-DC brake
A	41	Torque boost selection method		00
		00-Manual 01-Automatic
A241		Torque boost selection method (2. setting)
A	42	Value of manual torque boost setting		11
A242		Value of manual torque boost setting (2. setting)		11
A	43	Manual torque boost frequency adjustment (in %)		10.0
A243		Manual torque boost frequency adjustment (in %)
		(2. setting)
A	44	V/F characteristic setting		02
		00-Constant torque
		01-Variable torque	02-SLV
A244		V/F characteristic setting (2. setting)
A	45	V-Gain setting (in %)		100
A	51	Selection of DC braking operation		00
		00-NO 01- YES
A	52	DC braking frequency setting		0.5
A	53	DC braking waiting time setting		0.0
A	54	DC braking force setting		0
A	55	DC braking time setting		0.0
A	61	Frequency upper limit setting		0.0
A	62	Frequency lower limit setting		0.0
A	63,	Jump frequency setting		0.0
A	65,
A	67
A	64,	Jump frequency width setting		0.5
A	66,
A	68
A	71	Selection of PID control		00
		00-NO 01- YES
A	72	P (proportional) gain setting		1.0
A	73	I (integral) gain setting		1.0
A	74	D (differential) gain setting		0.0
A	75	Scale conversion of PID control setting		1.00
A	76	Feedback signal location setting		00
		00-Current 01-Voltage
A	81	Selection of AVR function		02
		00-Available 01-Not available
		02-Not available at deceleration
A	82	Selection of voltage of AVR function for the		FE:230/400
		motor		FE:230/460
A	92	Second acceleration time setting		15.0
A292		Second acceleration time setting (2. setting)
A	93	Second deceleration time setting		15.0
A293		Second deceleration time setting (2. setting)

(Table to be continued on next page)

(Continued from previous page)

Display		Function	Standard	Set
			Setting	Value
A	94	Selection of method to enable second	00
		acceleration/deceleration (acc2/dec2)
		00-Terminal 2CH 01-A 95 / A 96
A294		Selection of method to enable second
		acceleration/deceleration (acc2/dec2)
		(2. setting)
A	95	Changed frequency from acc1 to acc2 setting	0.0
A295		Changed frequency from acc1 to acc2 setting
		(2. setting)
A	96	Changed frequency from dec1 to dec2 setting	0.0
A296		Changed frequency from dec1 to dec2 setting
		(2. setting)
A	97	Pattern of acceleration setting	00
		00-Linear 01-S-curve
A	98	Pattern of deceleration setting	00
		00-Linear 01-S-curve

Display	Function	Standard	Set
		Setting	Value
b 01	Selection of restart mode	00

		00-Alarm 01-0.0Hz restart
		02-Motor speed match restart
		03-Motor speed match restart /decel to stop
b	02	Allowable undervoltage power failure time setting		1.0
b	03	Retry waiting time		1.0
b	12	Level of electronic thermal setting		Rated current
b212		Level of electronic thermal setting (2. setting)		of inverter
b	13	Selection of electronic thermal characteristic		01
		00-Reduced torque 01-Constant torque
b213 Selection of electronic thermal characteristic				01
		(2. setting)
b	21	Selection of overload limit operation mode		01
		00-NO 01-Accel & constant speed
		02-Constant speed
b	22	Level of overload limit setting		Rated current
				times 1.25
b	23	Rate of deceleration at overload restriction		1.0
b	31	Selection of software lock mode		01
		00-Terminal, no change
		01-Terminal, frequency change
		02-Keypad, no change
		03-Keypad, frequency change
b	81	Analog meter adjustment		80
b	82	Start frequency adjustment		0.5
b	83	Carrier frequency setting (kHz)		5.0
b	84	Initialization will 00-Clear trip history		00
		01-Restore data & parameters to factory settings
b	85	Selection of initialized data		-FE:01 -FU:02
b	86	Frequency converted value setting		1.0
b	87	STOP key active in terminal mode		00
		00-YES 01-NO
b	88	Selection of operation when FRS signal is		00
		cancelled
		00-Restart at 0 Hz	01-Restart at motor speed
b	89	Selection of contents of remote display		01
		01-Frequency 02-Current 03-Direction
		04-PID feedback	05-Input terminal status
		06-Output terminal status 07-Scaled frequency
b	90	Rate of use (in %) of the regenerative braking		00
		resistor during 100 seconds
		(00= braking resistor not active)
b	91	Deceleration mode selection when using the		00
		STOP key
		00-Deceleration stop
		01-Free run stop (FRS)
b	92	Fan ON/OFF selection		00
		00-Fan is always on
		01-Fan is only on if the inverter/motor
		is running

Display			Function			Standard	Set
						Setting	Value
C	01	Function of input terminal 1				00
		00-FW (Forward run)		01-RV (Reverse run)
		02-CF1 (Multispeed 1)		03-Multispeed 2
		04-Multispd. 3 05-Multispd. 4 06-JG (Jogging)
		07-DB (Ext. DC braking) 08-SET (use 2. setting)
		09-2CH (2. stage accel/decel)			11-FRS (Free run
		mode) 12-EXT (Extern. trip)			13-USP-function
		15-SFT (Software lock) 16-AT (Analog input
		type) 18-RS (Reset)		19-PTC (only for termi-
		nal 5) 27-UP (remote control acceleration)
		28-DWN (remote control deceleration)
C	02	Function of input terminal 2 (See C 01)				01
C	03	Function of input terminal 3 (See C 01)				-FE:02 -FU:16
C	04	Function of input terminal 4 (See C 01)				-FE:03 -FU:13
C	05	Function of input terminal 5 (See C 01)				-FE:18 -FU:09
C	06	Function of input terminal 6 (See C 01)				-FE:09 -FU:18
C	11 –	Polarity input of terminal 1-6				00 / C 14 only:
C	16	00-Normally open	01-Normally closed			-FE:00 -FU:01
C	21	Function of output terminal 11				01
		00-RUN-signal 01-FA1 (frequency constant)
		02-FA2 (Frequency at set point) 03-OL (Over-
		load) 04-OD (PID deviating)			05-AL (Alarm)
C	22	Function of output terminal 12 (See C 21)				00
C	23	Function of FM terminal		00-Analog frequency		00
		01-Analog current	02-Digital frequency
C	24	Function of alarm terminal (See C 21)				05
C	31	Polarity of terminal 11				01
		00-Normally open	01-Normally closed
C	32	Polarity of terminal 12 (See C 31)				01
C	33	Polarity of terminal AL0/AL1				01
		00-Normally open	01-Normally closed
C	41	Level of overload signal setting				Rated current
C	42	Arrival frequency setting for acceleration				0.0
C	43	Arrival frequency setting for deceleration				0.0
C	44	Level of PID deviation signal setting				3.0

C81 Frequency command adjustment (terminal O) C 82 Frequency command adjustment (terminal OI)

C	91 – For further use, do not change.	-	-
C	95

Display		Function	Standard	Set
			Setting	Value
H 01	Autotuning mode:	00-Autotuning off	00
	01-Autotuning on	02-Autotuning/static

H	02	Motor data: 00-Standard Hitachi 01-Auto	00
H202		Motor data (2. setting)
H	03	Motor capacity	Depending
H203		Motor capacity (2. setting)	on model
H	04	Number of motor poles	4
H204		Number of motor poles (2. setting)
H	05	Motor constant Kp	20
H205		Motor constant Kp (2. setting)
H	06	Motor stabilization constant	100
H206		Motor stabilization constant. (2. setting)
H	20	Motor constant R1	Depending
H220		Motor constant R1 (2. setting)	on model
H	21	Motor constant R2
H221		Motor constant R2 (2. setting)
H	22	Motor constant L
H222		Motor constant L (2. setting)
H	23	Motor constant Io
H223		Motor constant Io (2. setting)
H	24	Motor constant J
H224		Motor constant J (2. setting)

H30 Motor constant R1 Autotuning

H230	Motor constant R1	Autotuning (2. setting)
H 31	Motor constant R2	Autotuning	These
H231	Motor constant R2	Autotuning (2. setting)	para-
H 32	Motor constant L Autotuning		meters
H232	Motor constant L Autotuning (2. setting)		must not
			be
H 33	Motor constant Io Autotuning
			changed!
H233	Motor constant Io Autotuning (2. setting)

H34 Motor constant J Autotuning

H234 Motor constant J Autotuning (2. setting)

6 7 8