Home Theater Direct Universal Touch Screen Remote Control 3 How to Set Up the Home Theatre Master Remote, 3.1 By Entering Device Code, 3.2 By Searching Through the Library, CH+, CH+, VCR, SAT, CTV, DVD, CH+, VOL

3 How to Set Up the Home Theatre Master Remote

3.1 By Entering Device Code

You may setup the remote by the following code entering instructions.

1.	Refer to the Device Code List, look up the 4-digit device
	code which corresponds to the brands of your A/V
	equipment. If there are more than one device code listed
	under your brand, try from the first code.
2.	Press a desired device mode key (e.g.	TV	, “	”
	icon will flash)

3.Hold down “ CH+ ” and “ VOL– ” on the remote simultane- ously for 2 seconds until the indicator lights up.

4.Input the 4-digit device code, the indicator should flash twice.

Turn on your device (e.g. TV), try the function keys on the remote. If your device (e.g. TV) responds to your invoked function correctly, you have entered the right device code. Otherwise, repeat the above setup instructions with the rest available device codes until your device (e.g. TV) responds to your invoked function, and most keys work correctly.

*Simply repeat the above procedures to enter the device codes for your VCR, SAT, DVD or CTV. (Remember to press a correct device mode key in step 2 above.)

Note:

–DVD, CTV, SAT and other device codes can be entered into any device modes except “TV” & “VCR” modes. Just simply press the device mode key and enter your 4-digit device code for DVD, CTV, SAT and other devices.

–If the indicator flashes 6 times in step 4, a wrong device code has been entered.You are required to repeat step 2 to 4 again.

Suggestion:

–If you cannot find a correct device code for your equip- ment, see “ 3.2 By Searching Through the Library ”.

3.2 By Searching Through the Library

If you cannot identify a correct device code for your equipment from the Device Code List, you may search the code through the library:

1.	Turn on your device manually (e.g. TV).
2.	Press a desired device mode key (e.g.	TV	, “	”
	icon will flash)

3.Hold down “ CH+ ” and “ VOL– ” on the HTMR simultane- ously for 2 seconds until the indicator lights up.

4.Enter a corresponding Magic Search Code from the following table. The indicator should go out immediately.

DEVICE TYPE:			TV	VCR	SAT	CTV	DVD
MAGIC SEARCH CODE:			0001	0002	0003	0004	0005
(e.g. press		device mode key, then press “ CH+ ”
(e.g. press	TV	device mode key, then press “ CH+ ”

and “ VOL– ”, and enter TV Magic Search Code 0001.)

5.Press the same desired device mode key again as in step 2 above. (e.g. TV )

6.Hold down “ CH+ ” and “ VOL– ” simultaneously for 2 seconds until the indicator lights up, and your HTMR is ready to start searching.

7. Aim the HTMR at your device (e.g. TV), press the “ ” key repeatedly, slowly and patiently until the device has been turned off. Once your device has been turned off, immediately press the device mode key (e.g. TV ) to lock in code and the indicator should go out.

*Simply repeat the above setup procedures to search the device code for your VCR, SAT, DVD or CTV. (Remember to press a correct device mode key and correct Magic Search Code in step 2 to 5 above.)

IMPORTANT:

–If the power on/off function of your device is not infra- red controlled — you need to follow step 2 to 6 above and start searching.

Press “ ” and another important function key alternately until your device responds to the expected function, press the device mode key (e.g. TV ) to lock in the code.

e.g. Press “	” & “ 1 ” alternately, or
e.g. Press “	” & “ 1 ” alternately, or
Press “	” &	” alternately.
Press “	” &	” alternately.

Note:

–DVD, CTV and other device codes can be searched and locked into any device modes except “TV” & “VCR” modes. Just simply press the corresponding device mode key in step 2 & 5 and enter an appropriate Magic Search Code for your DVD, CTV and other devices.