Manuals / Brands / Lawn and Garden / Lawn Mower / Honda Power Equipment / Lawn and Garden / Lawn Mower

Honda Power Equipment HRC7113 Replace Belt , BLADE BRAKE ADJUSTMENT

1 57

Download 57 pages, 2.46 Mb

MAINTENANCE & ADJUSTMENTS

Replace Belt

1. Move the blade control

OFF

and remove the belt

cover.

48-inch deck shown

2. Loosen the two nuts on the belt guide at the deck

pulley.

3. Starting at the engine pulley, lift the belt out of the

pulley grooves.

4. Install the new belt by first setting it in the deck pulley,

then the tensioner pulley, and finally the engine

pulley. .

5. Tighten the two nuts on the belt guide at the deck

pulley.

6. Adjust the belt tension and blade brake.

BLADE BRAKE ADJUSTMENT

Check the blade brake adjustments after the deck belt is adjusted or replaced.

Moving belts and pulleys can cause serious injuries.

Do not operate engine with the belt cover(s)

removed.

Before removing belt cover(s) for maintenance,

remove key from ignition switch and disconnect the

spark plug lead.

1. Fully lower the rear of the deck, move

the blade control

OFF,

and remove the

belt cover(s).

2. Remove the hairpin clip and lower

washer from the brake rod at the pivot ___

plate. The rod should slip freely in and

out of the hole in the arm. If not, screw

the rod in or out of the pivot at the

tensioner arm until it’s a slip fit. ..__-. -

3. Install the rod in the pivot plate with two

washers and two hairpin clips as shown.

4. Start the engine and engage and

release the blade control several times. ==:--.-

--__..-.--

Confirm that the brake operates

correctly.

5. Install the belt cover.

41

Contents

Main Page Page A FEW WORDS ABOUT SAFETY Safety Labels - Instructions Safety Section Safety Headings Contents Page Page IMPORTANT MESSAGE TO EMPLOYERS Page Page Controls & Indicators \ LOCATIONS CONTROLS Fuel Valve ignition Switch Throttle Transmission Shift Lever 0 Blade Control Page Page Transporting and Storing TRANSPORTING YOUR MOWER 13 STORAGE PREPARATION Cleaning the Engine Fuel Engine Oil Grease Tires STORAGE PRECAUTIONS REMOVAL FROM STORAGE Before Mowing Page Operating the Mower STARTING THE ENGINE USING THE DIRECTION CONTROLS Moving Forward Steering the Mower Stopping the Mower Reversing the Mower Making an Emergency Stop STARTING TO MOW ADJUSTING YOUR SPEED MOWING TIPS Mowing on Slopes PARKING THE MOWER Maintenance & Adjustments THE IMPORTANCE OF MAINTENANCE 23 MAINTENANCE SAFETY Safety Precautions - Carbon monoxide poisoning from engine exhaust. - Injury from moving parts. - Burns from hot parts. EMISSION CONTROL SYSTEM INFORMATION Source of Emissions Tampering and Altering Problems that may Affect Emissions Replacement Parts Maintenance Page AIR CLEANER a. FUEL Fuel tank capacity: 24.6 liters, 6.5 gallons Refueling Fuel Recommendation Changing the Fuel Filter ENGINE OIL Checking the Level Recommended Oil Changing the Engine Oil Changing the Engine Oil Filter SPARK PLUG Recommended Types - Checking the Spark Plug VALVE CLEARANCE a. CARBURETOR IDLE SPEED 1750-1950 rpm THROTTLE CABLE MAXIMUM NO-LOAD SPEED 3550 *50 rpm 34 LUBRICATION POINTS, CONTROL LINKAGE ADJUSTMENT BRAKE LINING THICKNESS TIRES . 36 FRONT TIRE PRESSURE: 193 KPA (28 PSI) REAR TIRE PRESSURE: 103 KPA (15 PSI) CUTTING HEIGHT Front Wheel Adjustment Rear Deck Adjustment BLADES Inspecting the Blades Removing the Blades Installing the Blades DECK BELT ADJUSTMENT AND REPLACEMENT Adjust Belt Tension Replace Belt BLADE BRAKE ADJUSTMENT BLADE BELT ADJUSTMENT AND REPLACEMENT Inspect and Adjust (hook-to-hook): 120 - 140 mm (4% - 5% in) Replace 0 DRIVE BELT REPLACEMENT Remove Install Troubleshooting ENGINE Doesnt Start Low Power MOWER Doesnt Move Pulls To One Side Cuts Poorly Specifications MOWER ENGINE Additional Information MANUAL EN ESPAROL HONDA PUBLICATIONS Shop Manual Parts Catalog Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: OXYGENATED FUELS MODIFICATION FOR HIGH ALTITUDE OPERATION SPARK ARRESTER SERVICE (OPTIONAL EQUIPMENT) Index A B C D