Honeywell 500-XCL5010 SAFETY INSTRUCTIONS

EXCEL 500/600 INSTALLATION INSTRUCTIONS

SAFETY INSTRUCTIONS

— When performing any work (installation, mounting, start- — Use only accessory equipment which comes from or has

up), all instructions given by the manufacturer and in been approved by Honeywell.

particular the safety instructions provided in the

Installation Instructions are to be observed.

CAUTION

— The Excel 500/600 controller may be installed and Disconnect the power supply before you start to install

mounted only by authorized and trained personnel. the Excel 500/600 Controller. Do not reconnect the

power supply until you have completed installation.

— If the unit is modified in any way, except by the

manufacturer, all warranties concerning operation and

safety are invalidated. CAUTION

— Make sure that certain local standards and regulations Disconnect the power supply before plugging in or

are observed at all times. Examples of such regulations removing the communication module (Excel 500-

are VDE 0800 and VDE 0100. XCL5010).

5 EN1R-1047GE51 R0902

Contents

Main Excel 500/600 CONTROL SYSTEM INSTALLATION INSTRUCTIONS CONTENTS Page Page REVISION OVERVIEW EXCEL 500/600 INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS EXCEL 500/600 INSTALLATION INSTRUCTIONS MOUNTING Control Unit Installation Excel 500/600 Housing Layout (not XCL5010) Excel 500/600 Internal Bus Wiring (not XCL5010) Module Locations (not XCL5010) Coding the Terminal Block (not XCL5010) Setting the Module Address (not XCL5010) Installation Inside a Control Panel Excel 500/600 Page Excel 500-XCL5010 Excel 500-XCL5010 Communication Module Installation through a Control Panel Door (not XCL5010) External Installation of XI582AH Operator Interface Deactivating Backlit Display of the XI582AH Distributed I/O Installation Page Page Page Battery Activation during Commissioning (XC6010, only) Replacing the Battery Dismantling the Control Panel Unit Dismantling the Control Panel Door Unit Dismantling the Housing Cover Dismantling the Excel 500-XCL5010 Control Panel Unit Dismantling the XI582AH Operator Interface ELECTRICAL CONNECTIONS Cable Routing Shielding Input / Output Module and Power Supply Cables Shielding of Data-Transmitting Cables Grounding (XC5010C / XC6010, only) XC5010C / XC6010 Cable Lengths and Sizes Lightning Protection Summary of Internal Modules Line Power Supply XC6010 Computer Module XC5010C Computer Module XP502 Power Supply Module XP502 with External UPS XAPU 24-2F (Internal Modules, Only) XP502 with External UPS XAPU 24-2F (Distributed I/O Modules, Only) XP502 with External UPS XAPU 24-2F (Distributed I/O and Internal Modules) XF521A Analog Input Module XF526 Analog Input Module XF523A Digital Input Module XF522A and XF527 Analog Output Modules XF524A and XF529 Digital Output Modules XF525A Three-Position Output Module Excel 500-XCL5010 Serial Port MMI Connection Power Supply Screw Terminal Block Installation Procedure Pull-Up Resistor Handling (O.S. 2.04.00 or higher, except for XFL521A) Page COMMUNICATIONS LONWORKS Bus Wiring LONWORKS Bus Termination System Bus (C-Bus) Submodule Selection (XC6010) System Bus Cable Specification C-Bus Extension by Using Repeaters C-Bus Termination (Excel 600) C-Bus Termination (Excel 500) C-Bus Termination (Excel 500-XCL5010) Excel 600 Cable Specifications Excel 500 Cable Specifications Excel 500-XCL5010 Cable Specifications MMI Cables Modem or ISDN Terminal Adapter Connections Changing Between MMI and Modem Connection Page REMOTE COMMUNICATIONS Modem or ISDN Terminal Adapter Connections Modem Requirements No Set-up for Standard Modem Behavior Automatic Baudrate Synchronization TCP/IP Dial-Up via TCP/IP Modem XM500 GSM Communication (Europe, only) M20T Safety Precautions Required Third-Party Equipment Serial Cable GSM Antenna Requirements Antenna Examples GSM Antenna Installation M20 Terminal Set-up