Under no circumstances should the outer wall of the window frame be penetrated by the Forstner bit.
5800MICRA Wireless Recessed Transmitter
Installation Instructions
GENERAL INFORMATION
The 5800MICRA wireless recessed transmitter is a reed switch magnetic contact transmitter that allows the transmitter to be concealed from view when installed in a window. It is intended for use only with alarm systems that support 5800 series devices. The transmitter is powered by a
Programming the ID Number
Figure 1
1 Measure & Drill
Horizontal | |
Sliding | Sash |
|
Using a 3/4" Forstner Drill Bit with a stop collar, drill into the vinyl window mainframe.
Side mount transmitter on Vinyl Sliders
WARNING: under no circumstances should the outer wall of the window frame be penetrated by the Forstner bit.
Vertical Sliding
Sash
Sill mount transmitter on Hung Windows
Each 5800MICRA has its own unique identification code (serial number) permanently assigned during manufacturing.
The control panel is required to "enroll" the transmitter's ID during installation of the alarm system. The zones input type should be enrolled as "RF" (i.e. Supervised RF) Type (mandatory for all UL installations).
Refer to the control panel's installation instructions for further details.
PRELIMINARY CONSlDERATlONS
Measure 3" down from the inside top corner of the mainframe and mark the center point for the hole the 5800MICRA transmitter will be inserted into.
Place a corresponding mark also on the sash insert that will be used in this position.
inner wall
of window frame
3/4" Forstner drill bit
0.5"
< extrusion hollow >
11/32" core depth
outer wall of window frame
Read all of this and the next section before installing the unit.
1. Select a location for the transmitter on the frame of the window. |
Do not use on metal frame doors or windows. |
5800MICRA TRANSMITTER |
The 5800MICRA transmitter will require a 3/4" diameter hole (using |
a 3/4" Forstner bit) drilled into the edge of the window frame no more |
than 11/32" deep. Its accompanying magnet will need a 3/4" diameter |
hole drilled in the side of the window sash, no more than 11/32" deep. |
BEFORE DRlLLlNG ANY HOLES, SEE ITEM 2 BELOW AND MOUNTlNG |
SECTION ON PAGE 2. |
FOR VINYL SLIDING WINDOWS the preferred direction of mounting is vertical. |
FOR HUNG WINDOWS the 5800MICRA must be mounted horizontally in the |
window sill with the accompanying magnet mounted in the lower window sash. |
2 Place and Set
Insert the 5800MICRA's antenna into the extrusion hollow then press the transmitter body into the cored opening. Insure that the antenna moves freely in the window channel during installation.
NOTE: It is essential to the systems operation that the positioning of the iON icon on the transmitter point in the same direction as its corresponding sash magnet.
(see Step 1 - Measure & Drill in Figure 1) |
2. Before drilling any holes, tape the transmitter and magnet in their |
approximate locations (with battery installed and unit together as |
described under BATTERY INSTALLATION / REPLACEMENT (see Page 2) |
and conduct Go/No Go tests (see control's instructions) to verify |
adequate signal strength. Reorient or relocate the transmitter if necessary. |
Make sure that no more than a 1/2" gap will be present between the faces |
of the transmitter and magnet cases when they are installed and set. Also make |
sure the 'iON' graphic on the transmitter and magnet are aligned with each |
other as per Step 3 - Sash Magnet Placement in Figure 1. |
When installed, an alarm signal must be obtained before a clear space of 2" |
is reached as the window is opened. |
3 Sash Magnet
Placement
Using a 3/4" Forstner Drill Bit, drill into the window sash to a depth of 11/32" only.
Sash Magnet
Press the 5800MICRA transmitter's corresponding magnet into the cavity now drilled into the sash, making sure to position the iON icons to point in the same direction. NOTE: This point is essential to the systems proper operation.
Page 1