K14347 6/06 Rev. A
5878
- | Wireless Wall Transmitter |
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The 5878 is a
Do not use for system disarming in an area that requires security.
This device supports both Standard and
This device must be used with a receiver or control that supports high security mode i.e.: 5881EN, 5883, 6150RF, or 6160RF receiver or a LYNXR Series control panel (Revision 13.1 or higher if you intend to use it in high security mode).
The 5878 is powered by one replaceable lithium battery de- signed to provide up to four years of life. For battery installation, see Replacing the Battery.
|
| LED |
|
SERIAL #1 |
|
| SERIAL #1 |
LOOP 3 |
|
| LOOP 2 |
| AWAY | STAY |
|
SERIAL #1 |
|
| SERIAL #1 |
LOOP 4 | 1 | 2 | LOOP 1 |
| 3 | 4 |
|
SERIAL #2 |
|
| SERIAL #2 |
LOOP 3 |
|
| LOOP 2 |
5878 WALL TRANSMITTER* |
| |
* SERIAL #2 - LOOP 1 | = AWAY + 4 BUTTON |
|
LOOP 4 | = 3 + 4 BUTTONS | |
Figure 1 - 5878 Button Designations
PROGRAMMING
The 5878 is assigned two unique serial numbers during manufacture and each button, or button combination on the unit also has a distinct "loop" number (refer to Figure 1) that must be programmed into the control panel during installation. Assign each button, or button combination, to one of eight individual zones and designate the Input Type as "BR" (Button Type RF).
If you are enrolling the 5878 locally with an RF
Keypad, refer to the keypad’s Installation
Instructions for programming instructions.
1.When prompted, enter the serial number either by: Pressing and releasing the button (or buttons) that you are programming twice (wait about 5 seconds between button activations).or Manually through the keypad.
Notes: (1) To activate the transmitter, the 5878 buttons must be pressed and held for at least
(2)Serial #2 is one (1) digit higher than serial #1, which is printed on the rear of the transmitter.
Loop 4 Setup
Both of the Loop 4 buttons must be enrolled in the control, even if they will not be used. If one or both of the loops is not being used, program it as Zone Type 23 (No Alarm Response). Otherwise assign it to the desired zone type.
2.Exit Programming Mode after programming is complete. For complete details on how to program the transmitter's serial number at the control panel, see the control unit's installation instructions.
Assigning a 5878 to a User
On most control panels, if the wall transmitter is used for arming functions, you must assign it to a user in order for it to operate. This is accomplished through User Code programming at the control panel. See the control panel’s Installation and Setup Guide for specific instructions on programming User Codes.
If you are programming arming functions on both serial numbers, each serial number must be assigned to a separate user.
SELECTING STANDARD OR HIGH-SECURITY MODE
For use with LYNXR Series controls earlier than Revision 13.1, the Standard Mode must be selected.
To select Standard Mode, simultaneously press and hold the STAY, 1 and 2 buttons for three seconds.
To select
The LED flashes green when transmitting in Standard Mode and red when transmitting in
ACTIVATING HIGH-SECURITY MODE
To ensure proper functionality, the 5878 must be synced to the security system.
1.After selecting
2.To sync the transmitter with the receiver, simultaneously press and hold the AWAY, STAY, 1, and 2 buttons until the panel beeps (see Figure 1). For LYNXR Series controls proceed to step 4.
Note: The LYNXR Series panels will confirm the synchronization by sounding two beeps.
3.To sync the device in High Security Mode, press either the AWAY, STAY, 1, or 2 button ONCE, until the panel beeps indicating receipt.
4.To sync the second serial number of the wireless key with the receiver, simultaneously press and hold the 1, 2, 3, and 4 buttons until the panel beeps. For LYNXR Series controls proceed to step 6.
5.To sync the device in High Security Mode, press the 3 or 4 button ONCE, and hold until the panel beeps indicating receipt.
Note: If no beep is heard, exit Go/No Go mode, and repeat Steps 1 - 5.
6. Exit Go/No Go mode by entering user code + 1 (OFF).
