T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES
19 63-4355—4
3. Press increase ▲ or decrease ▼ until the desired
temperature offset is displayed (range is 0°F to 5°F).
4. Press Run Program.

Using Temporary Override

NOTE: The temporary override temperature is held for one,
three, eight or twelve hours (depending on installer
setup number 26) and then the thermostat returns to
the program.
1. Press Temporary Occupied.
NOTE: The default temperature setting is the
Occupied setpoint.
2. Press increase ▲ or decrease ▼ to change the default
setting by the offset (range is 0°F to 5°F), if desired.
NOTE: With zero offset, the default setting changes in
one degree increments. If the offset is 1 - 5, the
default setting changes by ± the offset.
3. Press Run Program to cancel the override.

Using Continuous Unoccupied

1. Press Continuous Unoccupied.
NOTE: The default temperature setting is the
Unoccupied setpoint. The default appears f or
approximately five seconds and then the room
temperature is displayed.
2. Press increase ▲ or decrease ▼ to change the default
setting, if desired.
3. Press Heat/Cool Settings to change between heat and
cool settings. Press increase ▲ or decrease ▼ to adjust
the temperature settings.
4. Press Run Program to cancel the Hold and return to the
program.

Changing Temperature Setpoint Until Next

Program Period

1. Press increase ▲ or decrease ▼ until the desired
temperature is displayed.
NOTE: If ▲ or ▼ appear under the temperature
display, it means that both the heat and cooling
setpoints are being adjusted. Tapping the key
changes both setpoints by one degree. Press
Heat/Cool Settings after the desired setpoint is
reached to review the settings.
2. Press Run Program to cancel the Hold and return to
the program.
OPERATION

T7200/T7300 Relay Logic

The T7200/T7300 contains three switching relays. In
conventional applications, the relays control first stage
cooling, first stage heating, and fan. In heat pump
applications, the relays control the heat pump compressor,
auxiliary heat, and the fan. Because of this change in
switching logic, it is important to use a Q7300C,D,
Q7300H2003, or Q7300H2011 Subbase when the T7300 is
set for heat pump applications and a Q7300A,G,
Q7300H2029 Subbase when the T7300 is set for
conventional applications.
The T7200D Relay Logic is for conventional applications.
The T7200E Relay Logic is for heat pump applications.
M4981A
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
M4954A
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Auto
System Fan
Mon
Room
AM
Occupied1
Heat
Run
Program
Override
Setting
Heat
M4982B
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
AutoSystem FanAuto
AM
Wed OverrideTemporaryRoomM4983B
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
M4954A
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Auto
System Fan
Mon
Room
AM
Occupied1
Heat
Run
Program
M4984B
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Continuous
Unoccupied Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Heat
Setting
M10232A
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Heat
Setting
M4954A
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Auto
System Fan
Mon
Room
AM
Occupied1
Heat
Run
Program
M4987B
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Heat
TemporarySetting
Occupied
M4954A
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Auto
System Fan
Mon
Room
AM
Occupied1
Heat
Run
Program