COMFORT LEVEL INDICATORS
This product is capable of detecting and displaying the current indoor comfort levels of surrounding environment. The comfort level is displayed on the weather station portion of the main unit’s display. It is based on the combination of the current indoor temperature and humidity readings. There are following comfort levels may be displayed: COMFORT (comfortable); WET (wet) and DRY (dry)
Indicator | Temperature | Humidity | Shows current | |
displayed | Range | Range | condition | |
|
|
|
| |
| 20˚C to 25˚C | 40%RH- | Ideal for | |
COMFORT | both relative | |||
| (68˚F to 77˚F) | 70%RH | humidity and | |
|
|
| temperature | |
|
|
|
| |
WET | OVER | Contains excess | ||
(23˚F to 122˚F) | 70%RH | moisture | ||
| ||||
|
|
|
| |
DRY | Below | Contains | ||
inadequate | ||||
(23˚F to 122˚F) | 40%RH | |||
| moisture | |||
|
|
| ||
|
|
|
|
13
WEATHER FORECAST
This unit is capable of detecting the atmospheric pressure changes. Based on collected weather data, it forecasts the weather for the next 12 to 24 hours.
When the display shows...
Forecast | Sunny | Partly | Cloudy | Rainy | Snowy |
is... |
| Cloudy |
|
|
|
NOTE: The weather forecast accuracy is approximately 70%.The main unit display shows forecasted, not current conditions. The SUNNY icon indicates clear weather, even when displayed during the
MAXIMUM AND MINIMUM READINGS
The maximum and minimum record of the indoor and remote temperature and humidity will be automatically stored in the memory of the main unit (receiver).
To display the minimum, maximum or the current reading press MEM button.
If no button is pressed for the next 15 seconds, the unit will return to the current temperature and humidity display. To clear the memory, press and hold MEM button for two seconds and all previously stored readings will be erased.
14
LOST COMMUNICATION
If the main unit display line for the remote sensor reading goes blank, press and hold DOWN ( 
) button for
2 seconds to begin a new signal search. If the signal still isn’t received, please make sure that:
•The remote sensor is in its proper location.
•The distance between main unit and remote sensor(s) is not over 200 feet (60meters).
•The path between units is clear of obstacles. Shorten the distance if necessary.
•Fresh batteries are installed correctly in both remote sensor and main unit.
If there is no reception, please perform the following steps:
•Bring the main unit and remote sensor close together.
•Remove four (4) small screws from the back of the remote sensor with small Phillips screwdriver, and open the battery compartment.
•Remove the batteries from the battery compartment and reinstall them in the same manner. Remote sensor LED indicator will flash showing transmission of the signal.
•Remove the batteries from the main unit and reinstall them in the same manner.
•On the main unit select the same channel number using CHANNEL button as set on the remote sensor. The remote temperature and humidity appeared on the main unit’s display will show that transmission is being received successfully.
15
TRANSMISSION COLLISION
Signals from the other household devices such as wireless doorbells, home security systems, and entry control, may interfere with this product or cause temporary reception interruption. This is normal and will not affect the general performance of the product. The transmission and reception of the temperature and humidity readings will resume once the interference subsides.
ANALOG CLOCK DISPLAY
Immediately after the battery installation, the clock’s hour and minutes “hands” will start moving and stop at 4:00, 8:00 or 12:00 position.
To program the desired time,
• Press and hold the CLOCK SET button, located inside the battery compartment – the MINUTE and HOUR hands will start moving clockwise
• Release the CLOCK SET button, once the MINUTE and HOUR hands have reached the desired time position. Immediately after releasing the CLOCK SET button, the SECONDS hand will start moving, confirming that clock is started.
ALARM
To set the time alarm,
• Turn the ALARM knob, moving the ALARM hand (smallest from three) to the desired alarm time
• Release the ALARM knob
• Slide ON/OFF switch to the ON position
DISABLING THE ALARM
Slide the ON/OFF switch on the main unit to the OFF position disabling the clock’s alarm.
SNOOZE
When the time alarm sounds, press the SNOOZE/LIGHT button to temporarily stop it. After the SNOOZE/LIGHT is depressed, the time alarm sound will resume in four minutes. If the alarm is not disabled after that, it will sound for two more minutes and then will stop by itself.
16
