Operation Manual

OSD Color Camera

VCC-600N/P

Thank you for choosing Honeywell VCC-600N/P camera. Please read these instructions carefully before operating this unit, and retain this manual for future reference.

If you have any problems with this camera, contact your local supplier to service.

CAUTION for SAFETY OPERATION

1.Water and Moisture

To prevent fire or shock hazard, do not expose this camera to rain or moisture.

2.Servicing

Do not attempt to disassemble or repair by yourself.

You may be exposed to dangerous voltage or other hazards. Note that all servicing is qualified service personnel. Modifications not approved by manufacturer could

void the user's authority to operate the equipment.

3.Power Sources

To prevent electric shocks and risk of hazards, do NOT use more than the specified power source.

4.Environment

Do not install too warm or too cold place. Recommended operation temperature is between -5and 50

5.Sunlight

Do not point the camera at the sun. CCD can be damaged.

6.Heavy Shock and Vibration

Do not drop the camera or subject it to heavy shock of vibration.

7.Install on an Unstable Place

Do not place or install this camera on an unstable place, stand, tripod, bracket or table. That may cause serious injury to people or damage to appliance.

8.When operation is incorrect or a malfunction is observed While operating, if any abnormal condition (strange sound, smell or smoke) or a malfunction (no pictures, etc.) is observed, stop using the camera immediately, turn the power off, then contact your supplier.

9.Cleaning

Turn the power off and wipe off the dirt with a dry soft cloth. If it is extremely dirty, use furniture cleaner to wipe it off. To clean the lens, use a blower or lens cleaning tissue. (available from any camera dealer)

10.Do not shoot any source of bright light.

If the objects contain very bright areas, bright vertical or horizontal lines may appear on the screen. This is called "smear" , a Phenomenon which often occurs with solid

-state pickups, and is not a malfunction.

11.Damage Requiring service

Unplug the camera from the power source and refer servicing to qualified service personnel under the following condition:

A. If the power-supply cord or plug is damaged.

B. If the camera has been exposed to rain or water.

C. If liquid has been spilled, or objects have fallen into the camera. D. If the camera does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the camera to its normal operation.

E. If the camera has been dropped or the cabinet has been damaged. F . If the camera exhibits a distinct change in performance.

G. Warranty is not covered in case of natural disaster or wrong Installation.

INSTRALLATION

Mounting a lens

1.Remove the Protective cap in front of the camera.

2.Confirm the mount ring whether it is for C or CS.

3.Attach the lens to the lens mount ring.

4.If the lens has an Auto Iris mechanism, connect the iris cable to the

LENS in rear of the camera.

In the case of having no iris amplifier : Set the slide switch to

DC (Down side).

In the case of having iris amplifier : Set the slide switch VSD (Upper side)

When connecting Auto iris lens, be sure to use the connector to be recommended by manufacturer.( E4-191, ChuoMusen, Japan)

VSD LENS PIN CONFIGURATION

DC IRIS LENS PIN CONFIGURATION

3

4

3

4

 

 

①③

 

 

①③

1

2

②④

1

2

②④

 

 

1.

Power(12V)

2.

No Connection

1.

Control -

2.

Control +

3.

Video Signal

4.

GND

3.

Drive +

4.

Drive -

Back focus adjustment

1. In case of fixed focus lens

Loosen the locking ring with L type wrench and set the focus ring of lens to infinity ( ).

Tune the mount ring to get a clear picture( distance from camera to object is more than 23m) and fasten the locking ring.

2. In case of zoom lens

Loosen the locking ring with L type wrench and set the lens to the maximum telephoto position. Then turn the focus ring to focus.

In the case of Auto iris lens only, shoot a comparatively dark object or reduce the ambient light so that the aperture is fully open.

Set the lens to its maximum wide angle position, and set the focus.

Repeat step and , until the difference between focusing position and is smallest.

When the best focusing point in found, fasten the locking ring.

Connection of power supply

Must be checked the power source from the external power supply before power on.

The contents of the package

Check the below contents

-VCC-600N/P Camera 1set

-Auto Iris Lens Plug

-L Type Wrench

-Operation Manual (English)

TROUBLESHOOTING

NAMES & FUNCTIONS

OSD MENU

SPECIFICATIONS

Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center.

In case of no image

Is the coaxial cable attached securely? Are the power and voltage normal?

Has the iris of the lens inside the camera been adjusted correctly?

In case of unclear image

Is the lens in focus?

Is the lens dirty?

Is the monitor adjusted correctly?

UP BUTTON

ENTER BUTTON

(-) BUTTON

DOWN BUTTON

(+) BUTTON

LENS CONNECTOR

LENS

GENERAL SETUP

SYNC

SYNC LEVEL adjustment (01255)

BURST

BURST LEVEL adjustment (01255)

CONTRAST

CONTRAST LEVEL adjustment

(01100)

 

RETURN

Return to the previous menu.

CAMERA SETUP

AE MODE

LENS MODE, SHUTTER, AGC, BRIGHTNESS, MAX AGC,

 

MAX FIELDS, etc.

WB MODE

AWC LOCK, AWC AUTO, ATW, INDOOR, OUTDOOR,

 

MANUAL, etc.

BLC MODE

OFF, BLC, WDR, BMB and

their level, area setting.

MODEL NAME

VCC-600N

 

VCC-600P

Operational

 

 

 

Video Standard

NTSC

 

PAL

Image Sensor

SONY 1/3Super HAD CCD

Total Pixel

410,000 Pixels

 

470,000 Pixels

Effective Pixel

380,000 Pixels

 

440,000 Pixels

Scanning System

525 Lines, 2:1 Interlace

 

625 Lines, 2:1 Interlace

Scanning Frequency

15.734kHz(H), 59.94Hz(V)

 

15.625kHz(H), 50Hz(V)

Sync System

INTERNAL

 

S/N Ratio

More than 50dB

 

Min. illumination

0.1lx (F=1.2, 50IRE)

 

0.001lx (F=1.2, 50IRE, MAX FIELDS x512)

 

 

 

Horizontal Resolution

540 TV Lines

 

Video Output

VBS 1.0Vp-p / BNC

Dirt of fingerprints on the lens can adversely affect the images. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available).

DIMENSIONS

POWER ON LED

This LED is ON

in power ON state.

ENTER

POWER

DC12V

+ - MD

VIDEO

CONT

DC VSD

VIDEO OUTPUT

Composite Video

Signal Output

PZM SET

Privacy Zone Masking function setting.

NIGHTSHOT

Day Night, Night Day mode setting.

CAMERA ID

Camera ID and Position setting.

RETURN

Return to the previous menu.

MEM FUNC. SETUP

DNR MODE

Digital Noise Reduction mode

setting. (OFFLOWHIGH)

PIP MODE

Picture-in-picture mode setting.

QUAD MODE

Quad display mode setting.

MD MODE

Motion Detection mode setting.

D.ZOOM

Digital Zoom setting. (OFF1.0x16.0x)

MIRROR

Mirror mode setting. (OFFH.MIRRORV.MIRRORFLIP)

RETURN

Return to the previous menu.

SPECIAL SETUP

SHARPNESS

Sharpness compensation setting. (0~15)

GAMMA

Gamma compensation setting. (0.36~1/USER , 8steps)

LANGUAGE

OSD Language setting. (ENG, KOR, JPN, CHI1, CHI2)

Lens Iris Control

MANUAL / DC / VSD

Electronic Shutter

1/60 ~ 1/100,000 sec

 

1/50 ~ 1/100,000 sec

AGC

 

OFF - 36dB

Back Light Compensation

OFF / BLC / WDR / BMB

White Balance

AWC LOCK / AWC AUTO / ATW / INDOOR / OUTDOOR / MANUAL

Electrical

 

 

 

Rated Voltage

 

DC12V ± 2V

Power Consumption

 

1.5W (max)

Mechanical & Environmental

 

 

Lens Mount

 

CS Mount

Weight

 

181g

Dimensions

61.6[W] x 52.4[H] x 77.8[D]mm

Front & Rear Color

Pantone Color 11C (Gray)

Body Color

 

Gray

Operating Temp.

 

-10°C ~ +50°C

Storage Temp.

 

-20°C ~ +70°C

Operating Humidity

90% RH (non-condensing)

Unit: mm

LENS

ENTER

VIDEO

CONT

POWER

DC VSD

+ -

Lens Type Select Switch

DC Lens: with no iris amp.

VSD Lens: with iris amp.

Power Input Terminal and MD Alarm Output

RETURN

Return to the previous menu.

DEFAULT SETUP

FACTORY DEFAULT

Set to the Factory Default.

RETURN

Return to the previous menu.

EXIT SETUP

SAVE AND EXIT

 

EXIT

 

RETURN

Return to the previous menu.

Honeywell Security Group

 

Honeywell Co., Ltd.

 

Address: 5F, Sangam IT Tower, B4 - 4block, 1590

 

Sangam-dong, Mapo-gu, Seoul 121-835, Republic of

 

Korea

Printed in Korea

TEL: +82 2 799 6020 / 6395 / 6006

FAX: +82 2 792 9011

D-100073-001, REV.0

E-mail: info.security@honeywell.com

Page 1
Image 1
Honeywell VCC-600N/P operation manual UP Button Enter Button Down Button + Button Lens Connector, General Setup