INSTALLATION IN FITTED KITCHENS

Fitting between existing cabinets

■The height of the dishwasher, 85 cm, has been designed in order to allow the machine to be fitted between existing cabinets of the same height in modern fitted kitchens (fig. 5).

The feet can be adjusted so that correct height is reached.

Underneath existing work top

(when fitting beneath a work top)

■In most modern fitted kitchens there is only one single work top under which cabinets and electrical appliances are fitted. In this case remove the work top of the dishwasher by unscrewing the screws under the rear edge of the top (fig. 6a).

IMPORTANT

After removing the work top, the screws MUST BE screwed again under the rear edge of the top (fig. 6b).

■The height will then be reduced to 82 cm, as scheduled by the International Regulations (ISO) and the dishwasher will fit perfectly under the kitchen working top (fig. 7).

WATER SOFTENER UNIT

Depending on the source of the supply, water contains varying amounts of limestone and minerals which are deposited on the dishes leaving whitish stains and marks.

The higher the level of these minerals present in the water, the harder the water is. The dishwasher is fitted with a water softener unit which, through the use of special regenerating salt, supplies softened water for washing the dishes. The degree of hardness of your water can be obtained from your water supply company.

Regulating the water softener

The water softener can treat water with a hardness level of up to 90°fH (French grading) or 50°dH (German grading) through 8 settings.

The settings are listed in the table below:

*The softener unit is set in the factory at level 4 (d4) as this satisfies the requirements of the majority of users.

Regulate the setting of your water softener unit according to the degree of hardness of your water as follows:

IMPORTANT

The dishwasher must be ALWAYS off before start this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 5 seconds,

UNTIL a brief audible signal sounds.

The current water softener setting level

will be shown on the display.

5

6

a

a

7

b

 

 

 

 

 

 

 

b

 

598 556/573

Opening the door

 

Closing the door

 

Water

Use of regenerating salt

 

 

 

hardness

Water softener setting

Level

°fH (French)

°dH (German)

 

 

 

 

 

0

0-5

0-3

NO

d0

 

1

6-10

4-6

YES

d1

 

2

11-20

7-11

YES

d2

 

3

21-30

12-16

YES

d3

 

*4

31-40

17-22

YES

d4

 

5

41-50

23-27

YES

d5

6

51-60

28-33

YES

d6

7

61-90

34-50

YES

d7

3.

Press the same button again to select

 

the required water softener level: each

 

time the button is pressed, the setting

 

will increase by one level. When you

 

have reached "d7", the display will go

 

back to "d0".

4.

Turn off the dishwasher by pressing the

 

"ON/OFF" button to confirm the new

 

setting.

WARNING!

If any problem occurs, turn the dishwasher off by pressing the "ON/OFF" button and start the procedure again from the beginning (STEP 1).

Put your hand into the recess and pull.

If the machine comes open while it is working, an electrical safety device automatically switches everything off.

IMPORTANT

For the machine to work properly, the door should not be opened while it is in operation.

Place the baskets in the machine.

Make sure that both the spray arms are free to rotate and are not obstructed by cutlery, crockery or pans. Close the door, pressing on it to make sure it is firmly shut.

Digital display

 

 

 

 

 

 

 

 

 

 

“ON/OFF”

 

 

“PROGRAMME SELECTION” button
button

 

 

 

 

 

8

9