Hoover HND 615 manual Changing a running program, Program operations, Program end, Option button

Changing a running program

Proceed as follows to change or cancel a running program:

■Hold down the current program button (with the LED on) for at least 3 seconds. The program LEDs (except for the "RAPID" program LED) will blink until all water is drained (if necessary).

The running program will be cancelled and the corresponding LED will start to blink.

IMPORTANT

To cancel the "COLD RINSE" program, simultaneously hold down the "RAPID" program button and "HALF LOAD" option button (the relevant LEDs will blink to confirm cancellation).

■At this point a new program can be set.

WARNING!

Before starting a new programme, you should check that there is still detergent in the dispenser.

If necessary, top up the dispenser.

If there is any break in the power supply while the dishwasher is operating, a special memory stores the selected programme and, when the power is restored, it continues where it left off (if it is necessary, the appliance will make a short thermal anti-shock programme before).

Program operations

When a program is running the relevant LED will remain on and the 3 “PROGRAM STATUS” LEDs ("WASH", "RINSE", and "DRY") will light singularly and in sequence to indicate the current phase.

Program end

The “PROGRAM STATUS” LEDs will turn off and the selected program LED (2 LEDs for the "COLD RINSE" program) will blink to indicate that the cycle has ended.

Dishes can now be removed and the dishwasher turned off by pressing the "ON/OFF" button or dishes can be loaded for new cycle.

Option button

"HALF LOAD" button

By using this option, it is possible to wash a smaller quantity of crockery: you should load only the upper basket for dishes and place cutlery in the tray in the bottom basket.

This reduces water and energy consump- tion and requires a smaller quantity of detergent.

IMPORTANT

This button MUST be set BEFORE the program starts.

"DELAY START" button

Dishwasher start time can be set with this button, delaying the start by 3, 6 or 9 hours.

Proceed as follows to set a delayed start:

■Press the "DELAY START" button (each time the button is pressed the start will be delayed by 3, 6 or 9 hours respectively and the corresponding time LED will light).

■To start countdown, press the selected program button (the relevant LED will stop blinking and remain on, while the set time LED will start to blink).

If a 9 hour delay is set, countdown will be displayed by the 6h LED after 3 hours and the 3h LED after 6 hours.

At the end of the last 3 hours (at the end of countdown) the 3h LED will stop blinking and remain on to indicate the washing phase and the program will start automatically.

If countdown has not ended, whereby the program has not yet started, it is possible to change or cancel the delayed start and select another program or to select/unselect the option button, proceeding as follows:

■Hold down the selected program button for at least 5 seconds (the corresponding LED will start to blink while the set time LED will stop blinking and remain on).

■Press the "DELAY START" button to set another delayed start time (the corresponding time LED will turn on) or cancel delayed start (corresponding time LEDs will all turn off).

■A new program can be set after a delayed time has been changed or cancelled (the corresponding LED will stop blinking and remain on) or an option button has selected or deselected.

Fault signals

If malfunctions or faults occur when a program is running the LED that corresponds to the selected cycle (2 LEDs for the "COLD RINSE" program) will blink rapidly.

In this case, turn the dishwasher off by pressing the "ON/OFF" button. After checking to make sure the water intel hose tap is open, that the drain hose is not bent and that the siphon or filters are not clogged, set the selected program again. If the anomaly persists, contact Customer Service.

IMPORTANT

This dishwasher is equipped with an anti-overflow safety device which will automatically empty any excess water should a problem occur.

WARNING!

To ensure the correct operation of the anti-overflow safety device, it is recommended not to move or to tilt the dishwasher during operation.

If it is necessary to move or to tilt the dishwasher, first make sure the washing cycle is finished and that no water is left in the tank.

24 25