INTRODUCTION IMPORTANT PRECAUTIONS

P R E - A S S E M B LY

DO NOT ATTEMPT TO LIFT THE TREADMILL!* Do not move or lift treadmill

WARNING from packaging until specified to do so in the assembly instructions. Failure to do so may result in injury! Remove plastic wrap from console masts.

Note: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before

completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

A S S E M B LY STEP 1

A S S E M B LY STEP 2

HARDWARE BAG 2 CONTENTS :

 

FLAT WASHER (E)

WAVY WASHER (F)

BOLT (D)

27 mm

29 mm

Qty: 1

Qty: 1

Qty: 1

 

 

LEAD WIRES

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

HARDWARE BAG 1 CONTENTS :

BOLT (A)

FLAT WASHER (B)

TEFLON WASHER (C)

15 mm

20 mm

18 mm

Qty: 1

Qty: 1

Qty: 1

BOLT (D)

FLAT WASHER (E)

WAVY WASHER (F)

Qty: 1

27 mm

29 mm

 

Qty: 1

Qty: 1

 

RIGHT CONSOLE MAST

MAIN FRAME

 

WAVY WASHER (F)

FLAT WASHER (E)

RIGHT CONSOLE MAST

 

ASSEMBLY

BEFORE YOU BEGIN

MAIN FRAME

LEFT CONSOLE MAST

WAVY WASHER (F)

CONSOLE CABLES

BOLT (D)

 

 

RIGHT LINKAGE ARM

 

FOOT LOCK LATCH

ELEVATION FRAME CONSOLE CABLES

PRE-ATTACHED BOLT

BEFORE YOU BEGIN

TREADMILL OPERATION

CONDITIONING TROUBLESHOOTING LIMITED GUIDELINES & MAINTENANCE WARRANTY

FLAT WASHER (E)

 

BOLT (D)

 

LEFT LINKAGE ARM

 

BOLT (A)

 

FLAT WASHER (B)

 

TEFLON WASHER (C)

ELEVATION FRAME

AOpen HARDWARE BAG 1.

BCut banding straps. Do not move or lift treadmill from packaging.

CMove left linkage arm into position. Insert bolt (A) and FLAT WASHER (B) into left linkage arm followed by a TEFLON washer (C) and attach to elevation frame.

DLift left console mast into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on its own.

EInsert bolt (D) and 1 FLAT washer (E) through left console mast followed by a WAVY washer (F) and attach to MAIN FRAME.

A. Pull LEAD WIRE through RIGHT CONSOLE MAST. After pulling the lead wire through the mast, the top of the console cables should be located at the top of the mast. Detach and discard lead wire.

B. Open HARDWARE BAG 2.

C. Move right linkage arm into position and attach to

ELEVATION FRAME.

Note: While holding RIGHT CONSOLE MAST in the upright position, tighten PRE-ATTACHED BOLT using T-wrench to attach RIGHT LINKAGE ARM.

D. Attach RIGHT CONSOLE MAST to MAIN FRAME using 1 BOLT (D), 1 FLAT WASHER (E) and 1 WAVY WASHER (F).

E. Lift the running deck until lock latch on side of treadmill is fully engaged.

F.Remove console from box and place out of the way.

G.Lower the treadmill running deck from the folded position by stepping on LOCK LATCH on lower right side.

*Note: If you have attempted to move the treadmill from the box and the machine has sprung open and cannot be assembled, refer to the troubleshooting section in order to restore the treadmill to its proper position.

1

3

2



TREADMILL OPERATION

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES

CT83_Treadmill_Rev.1.7.indd 8-9

7/9/07 10:01:25 AM

Page 5
Image 5
Horizon Fitness CT83 manual Open Hardware BAG, Elevation Frame, Remove console from box and place out of the way

CT83 specifications

The Horizon Fitness CT83 is a remarkable treadmill designed for both novice users and fitness enthusiasts, offering an unparalleled blend of features, technologies, and characteristics that enhance the workout experience. This treadmill stands out in the crowded fitness market, providing users with a high-quality training platform that meets a variety of fitness goals.

One of the noteworthy features of the CT83 is its robust motor. Equipped with a powerful 2.5 HP continuous duty motor, it delivers a smooth and consistent performance, allowing users to achieve higher speeds and endurance levels without compromise. Whether users are walking, jogging, or running at higher speeds, the motor ensures stability and reliability throughout their workouts.

The running surface of the CT83 is another highlight, offering a generous 20-inch width and 55-inch length. This spacious deck accommodates users of all sizes and provides ample room to move comfortably, reducing the risk of injury. Moreover, the deck is cushioned with a state-of-the-art FlexDeck technology, designed to reduce impact on joints by up to 30% compared to running on traditional treadmills. This makes it particularly suitable for long-distance runners or individuals who may be prone to joint issues.

The CT83 boasts an intuitive console that features a 5-inch LED display, providing real-time feedback on essential workout metrics such as time, distance, speed, calories burned, and heart rate. Heart rate monitoring is facilitated through built-in sensors on the handlebars, allowing users to maintain their desired training zones for optimal results.

Another significant aspect of the CT83 is its variety of workout programs. It comes with several pre-set workout programs designed to keep users engaged and challenged. With options ranging from interval training to calorie burning and distance goals, users can easily customize their workouts to align with personal fitness objectives.

In terms of convenience, the CT83 is foldable, making it easy to store when not in use. It features convenient transport wheels for effortless movement, allowing users to save space in their homes without sacrificing workout quality.

Overall, the Horizon Fitness CT83 delivers a well-rounded treadmill experience marked by its distinct features, advanced technologies, and user-friendly design. It stands as an excellent choice for anyone looking to enhance their cardiovascular fitness while enjoying a comfortable and efficient workout environment.