How to run a wash cycle or a drying cycle
WARNING: before you use the
EN time, run a wash cycle with detergent and no laundry, using the 90° cottons cycle without
1.SWITCH THE MACHINE ON. Press the 
button. All the indicator lights will illuminate for 1 second; the
indicator light corresponding to the 
button will then remain lit in a fixed manner and the START/PAUSE indicator light will flash slowly.
2.LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of wash cycles on the following page.
3.MEASURE OUT THE DETERGENT. Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in “Description of the machine”.
4.CLOSE THE PORTHOLE DOOR.
5.SELECT THE PROGRAMME. Turn the WASH CYCLE SELECTOR KNOB right or left, until you have selected the desired wash cycle. A temperature and spin speed is set for each wash cycle; these may be adjusted.
6.CUSTOMISE THE WASH CYCLE. Use the relevant buttons on the control panel:
Modify the temperature.
The machine automatically displays the maximum temperature values set for the selected cycle, or the most
pressing the 
button, until the cold wash (
) setting is reached. If this button is pressed again, the maximum values are restored.
Setting the drying cycle.
The first time the button 
is pressed, the machine will automatically select the maximum drying cycle which is compatible with the selected wash cycle. Subsequent presses will decrease the drying level and then the drying
time, until the cycle is excluded completely (
). If this button is pressed again, the maximum values are restored.
Drying may be set as follows:
A - Based on a set time period: between 20 and 180 minutes. B- Based on the desired laundry dryness level:
Iron “L1”: suitable for clothes which will need ironing afterwards. the remaining dampness softens creases, making them easier to remove.
Hanger “L2”: ideal for clothes which do not need to be dried fully.
Cupboard “L3”: suitable for laundry which can be put back in a cupboard without being ironed.
Extra “L4”: suitable for garments which need to be dried completely, such as sponges and bathrobes.
If your laundry load to be washed and dried is much greater than the maximum stated load, perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back in the drum. At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the remainder of the load.
A
Drying only
Use the cycle selector knob to select a drying cycle 
-
-
)
.
Set a delayed start.
Press the button until you have reached the desired delay time. During the setting process, the delay time is shown on the display and the 
symbol flashes. After selecting a delayed start time, the fixed 
symbol and the cycle duration will appear on the display. Press the button once to display the selected delay time. To remove the delayed start option, press the button until the display shows the text OFF; the 
symbol will disappear.
!Once the START/PAUSE button has been pressed, the time delay may only be decreased.
Modify the cycle settings.
Press the OPTION buttons to customise the wash cycle in accordance with your own requirements.
•Press the button to activate the option; the corresponding indicator light will switch on.
•Press the button again to disable the option; the indicator light will switch off.
! If the selected option is not compatible with the selected wash cycle, this incompatibility will be signalled by the flashing of the indicator light and a sound alert
(3 beeps); the option will not be activated.
! If the selected option is not compatible with another option that has been selected previously, the indicator light corresponding to the first option selected will flash and only the second option will be activated; the indicator light corresponding to the button will remain lit in a constant manner.
7.START THE PROGRAMME. Press the START/PAUSE button. The corresponding indicator light remains lit in a
fixed manner and the porthole door locks (the 
LOCK indicator light illuminates). The icons corresponding to the wash cycle phases will light up during the cycle to indicate which phase is currently in progress. To change a wash cycle once it has already started, pause the
PAUSE button; if the LOCK 
indicator light is switched off you may open the door. Press the START/PAUSE button again to restart the wash cycle from the point at which it was interrupted.
8.THE END OF THE WASH CYCLE. This is indicated by the illuminated text END. The porthole door may be opened immediately. If the START/PAUSE indicator light is flashing, press the button to end the cycle. Open the door, unload the laundry and switch off the machine.
!If you wish to cancel a cycle which has already begun,
press and hold the 
button until the cycle stops and the machine switches off.
8
