Hotpoint DX 1032 CX If something goes wrong, Problem, Possible cause, Solution, heat could cause

Models: DX 1032 CX

1 28
Download 28 pages 45.2 Kb
Page 26
Image 26
Problem

If something

goes wrong...

 

￿

￿

 

 

 

 

 

 

 

 

 

 

 

GB

 

 

 

 

 

 

 

 

 

Oven light does not

The oven lamp is not covered by the guarantee. The part is easily changed (see the section

 

 

 

 

 

 

 

on oven lamp replacement). A new lamp may be obtained from our Parts department see

 

 

 

work

back page.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Draught from

A gentle flow of air will be blown from beneath the control panel when the appliance is

 

 

 

used. If the appliance is still warm, this cooling fan may run on, or restart itself when all

 

 

 

 

beneath control

 

 

 

controls have been turned off. The fan will stop once the appliance has been cooled. This

 

 

 

 

panel

 

 

 

is normal and not a fault.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Steam /

Steam is a by - product of cooking any food with a high water content. To help minimise

 

 

 

always:

 

 

 

 

 

 

 

Condensation in

 

 

 

 

 

 

 

a) Try to avoid leaving food in the oven to cool after being cooked.

 

 

 

 

the oven after use.

 

 

 

b) Use a covered container, wherever possible.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If you have been through the above list and there is still a problem, contact Service (see back page).

 

 

 

 

 

 

 

 

Problem

 

Possible cause

 

Solution

 

 

The “Clock button” and the

The appliance has just been

 

Set the clock.

 

 

digits on the display flash.

connected to the electricity

 

 

 

 

 

 

 

 

mains or there has been a blackou

 

 

 

 

 

 

A programmed cooking mode

There has been a blackout.

 

Reprogram the cooking mode.

 

 

does not start.

 

 

 

 

 

 

 

 

Only the high luminosity

The appliance is in standby mode

 

Press any button to exit

 

 

“Clock button” is lit.

 

 

standby mode.

 

 

An automatic mode has been

The temperature inside the oven

 

Wait for the oven to cool down.

 

 

 

selected. “Hot” appears on the

is higher than the suggested value

 

 

 

 

 

 

display and cooking does not start

for the selected mode.

 

 

 

 

 

 

Fan-assisted cooking has been

Positions 1 and 5: the direct

 

We recommend switching

 

 

selected and the food looks burnt.

heat could cause

 

dripping pan positions halfway

 

 

 

 

temperature-sensitive

 

through cooking.

 

 

 

 

foods to burn.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Disposal of your product

To minimise the risk of injury to children please dispose of your product carefully and safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off flush with the appliance and always ensure that no plug is left in a condition where it could be connected to the electricity supply.

To help the environment, Local Authority instructions should be followed for the disposal of your product.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

26

Page 26
Image 26
Hotpoint DX 1032 CX If something goes wrong, Problem, Possible cause, Solution, Disposal of your product, heat could cause