Hotpoint HXQB 9.8LTI manual TBOX-GLASS controls, Maintenance and care

TBOX-GLASS controls

Models with Touch control glass (basic)

The hood can be turned off manually by pressing the T1 button (ON/OFF). If the timer is set, the hood turns off GB automatically when the set time runs out.

T1 T2 T3 T4 T5 T6 T7 T8

Maintenance and care

Caution! Before cleaning or servicing the unit, disconnect it from the mains by pulling the power plug or disconnecting the main circuit breaker.

T1 motor ON/OFF	First cleaning
When the button is pressed with the hood off, the first speed
is set. When the button is pressed during operation, the	• Remove the protective film
hood switches OFF.	• Clean with a damp sponge and a little neutral soap
	• Rinse off with a damp cloth
T2 Speed 1	• Dry with a soft cloth; if the hood is stainless steel, dry
When the button is pressed the hood switches from the	along the metal's grain
previous status to speed 1.	Periodic cleaning
T3 Speed 2	The hood must be cleaned frequently (at least as often as
When the button is pressed the hood switches from the	you service the grease filter), inside and out. Use a damp
previous status to speed 2.	cloth and a neutral liquid detergent with lukewarm water.
	Do not use abrasive or corrosive products.
T4 Speed 3	Warning: Failure to observe the hood cleaning and filter
When the button is pressed the hood switches from the	cleaning/replacement instructions can result in fires. Follow
previous status to speed 3.	the instructions carefully. The manufacturer is not liable for
	any damage to the motor or fires caused by incorrect care
T5 Booster	or failure to follow the above instructions.
When the button is pressed the hood switches from the	Servicing the grease filter (A)
previous status to intense speed. The setting is limited by
time; when the time elapses the hood goes back to the speed		The grease filter retains the
set previously; when a speed button is pressed (T2, T3 or		particles of grease produced
T4), the selected speed is set as you leave the booster mode.		during cooking; it must be
		cleaned at least once a month
T6 Timer	A	with a non - aggressive
By pressing T6 once, a timer setting can be associated to		detergent, either by hand or
each speed [V](V1 – 30 min, V2 – 20 min, V3 – 10 min), after		with a low temperature, short
which the hood turns OFF automatically. The timer can be set		dishwasher cycle.
for manual speeds only and not for the booster.		To extract the grease filter,
		pull the spring loaded handle.
T7 Antigrease and odour filter signal	If washed in a dishwasher, the metal filter may change
The antigrease (A) and odour (B) filters need cleaning/	colour, but this does not affect its performance.
replacing after a certain number of hours of use (the latter	Servicing the charcoal filter (B)
for filtering hoods only).
The time for cleaning/replacement is signalled by the	The charcoal filter retains unpleasant cooking odours.
flashing of the coloured LED associated to the filter (white	The filter saturates after a variable time, depending on the
for antigrease filters, red for odour filter).	type of cooking and how often the grease filter is cleaned.
The LED is turned off by pressing the T7 button after	The cartridge must be replaced at least once every twenty
cleaning/replacing the filters.	months.
	This filter can NOT be washed or regenerated
T8 lights ON/OFF		Disassembly: Remove the
It turns the work lights of the hood on and off.		activated-carbon filter by
	B	pressing the two front levers
Hood configuration		which secure it to the hood.
The configuration menu is accessed with the product off
by pressing T5 and T6 for 6 seconds. T7 turns on at this
point to indicate the type of installation through two colours
of the LED: white for extractor installation (default), red for
filtering installation. The installation type can be changed
by pressing T7 cyclically with the consequent alternation
of the LED colours.

Hood off

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

11