Hotpoint LFT 228 manual Start-up and use, Starting the dishwasher, Measuring out the detergent

Start-up and use

Starting the dishwasher

EN

1.Turn the water tap on.

2.Open the door and press the ON/OFF button: you will hear a short beep and the display and option indicator lights switch on.

3.Measure out the detergent (see below).

4.Load the racks (see Loading the racks).

5.Select the wash cycle in accordance with the type of crockery and its soil level (see Table of wash cycles), by pressing the P button.

6.Select the wash options* (see adjacent information).

7.Start the wash cycle by shutting the door: a long beep signals the start of the wash cycle.

8.Two short beeps and one long one indicate the end of the wash cycle and the wash cycle number flashes on the display. Open the door, switch off the appliance by pressing the ON/ OFF button, shut off the water tap and unplug the appliance from the electricity socket.

9.Wait for a few minutes before removing the crockery, in order to avoid burns. Unload the racks, beginning with the lower level.

AUTO WASH CYCLES*: this model of dishwasher is equipped with a special sensor which can be used to assess the level of soiling and automatically select the most efficient and economic wash cycle accordingly.

The duration of the auto wash cycles may vary due to the operation of the sensor.

- The machine will switch off automatically during certain periods of inactivity, in order to minimise electricity consumption.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection process it is possible to change the cycle, provided that it has only just begun: open the door, avoiding the escaping steam, and press and hold the ON/OFF button; the machine will switch off with a long beep. Switch the machine back on using the ON/OFF button and select the new wash cycle and any options desired; start the cycle by closing the door.

Adding extra crockery

Without switching off the machine, open the door, taking care to avoid the escaping steam, and place the crockery inside the dishwasher. Close the door: the cycle starts from the point at which it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a power cut, the cycle stops. It starts again from the point at which it was interrupted once the door has been shut or once the electricity supply is restored.

Measuring out the detergent

A good wash result also depends on the correct amount of detergent being used; exceeding the stated amount does not result in a more effective wash and increases environmental pollution.

Only use detergent which has been specifically designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam residue remaining in the machine after the cycle has ended.

The use of tablets is only recommended for models which offer the MULTI-FUNCTIONAL TABLETS option.

To achieve the best results from each washing and drying cycle, powder detergent, rinse aid liquid and salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

D		1. Open cover C by pressing button
A	B	D.
		2. Pour in the detergent after
		consulting the Table of wash cycles:

• For powder detergent use compartments A and B.

• For detergent in tablet form: when the cycle requires 1 tablet, place it in

Ccompartment A and close the cover; when it requires 2, place the second tablet at the bottom of the appliance.

3.Remove detergent residues from the edges of the compartment and close the cover until it clicks.

Wash options

If an option is not compatible with the selected was cycle (see Table of wash cycles), the corresponding LED flashes rapidly 3 times and 2 short beeps will sound.

Delayed start*

It is possible to delay the start time of the cycle by 3, 6 or 9 hours.

1.Press the DELAYED START button: every time it is pressed a buzzer sounds and the selected period of time is displayed.

2.Select the wash cycle and shut the door: after the beep sounds, the timer begins counting down.

3.Once this time has elapsed, the indicator light switches off and the wash cycle begins.

To adjust the delay time and select a smaller period of time, press the DELAYED START button. To cancel it, press the button repeatedly until the selected delayed start indicator light switches off. The wash cycle will start automatically as soon as the door is shut.

* Only available in selected models.

8