HP ColorPro CAD manual Memory Manager

139

141

142

143

144

145

146

147

148

149

151

152

153

154

155

156

157

158

159

161

162

163

164

165

166

167

DEFERRED_ERROR_TRAP NVM_ERR_NOT_INIT NVM_ERR_GENERIC NVM_ERR_DEVICE_ABSENT NVM_ERR_WRITE NVM_ERR_READ NVM_ERR_READBACK NVM_ERR_DATA_NOT_VALID NVM_ERR_UNKNOWN_TAG NVM_ERR_UNKNOWN_FORMAT NVM_ERR_BAD_CHIP_TAG NVM_ERR_BAD_FAMILY NVM_ERR_BAD_COLOR NVM_ERR_TSR_VALUE NVM_ERR_DROP_VALUE NVM_ERR_BAD_TOKEN NVM_ERR_BAD_WRITE_PROT NVM_ERR_BAD_MODEL_NUM NVM_ERR_INCOMPAT_INK NVM_ERR_BAD_MFG_WEEK NVM_ERR_SPARE NVM_ERR_POOL_ALLOC_FAIL NVM_ERR_ACU_BAD_SIZE NVM_ERR_DUPLICATE_TAG NVM_ERR_TOKEN_MISLOC

NVM_ERR_I2C_CONF_FAIL

Memory Manager

Error happened during power up but printer recovered Not used

Not used

NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used Penhead and cartridge errors –Not used System recources – Reset printer

Penhead and cartridge errors –Not used

Penhead and cartridge errors –Not used

Penhead and cartridge errors –Not used

Bus used for connecting devices on the PCA experiences error. Reset Printer => Replace PCA

Printer error-trapped in a previous lifetime.

Attempt to read/write before init.

Non-specific NVM error.

Requested memory device did not respond.

Protocol error on write operation to NVM.

Protocol error on read operation to NVM.

Failed readback/verify after write.

Device works OK.

Data tag invalid.

Chip functions but has invalid format.

Acumen's chip tag unrecognized.

Acumen's family ID unrecognized.

Acumen's color code did not match device ID.

Acumen TSR value = 0.

Acumen drop volume = 0.

Token area failed zero-write self test.

Write-protect area failed self test.

Acumen Model Number field out of range.

Non-approved bit and "JETSERIES".

Mfg week > 51.

Previously was Gas Gauge Gap.

No memory to allocate pool from.

Token Write-protected or Scratchpad size = 0. Two identical tags were found in an Acumen chip. Status superfield not located in token area.

A failure was detected on the serial bus used to access NVM devices (I2C bus). The following extended error codes apply :

001= STUCK_LO_SDA

002= STUCK_HI_SDA

004= STUCK_LO_SCL

005= STUCK_LO_SCL + STUCK_LO_SDA

006= STUCK_LO_SCL + STUCK_HI_SDA

008= STUCK_HI_SCL

009= STUCK_HI_SCL + STUCK_LO_SDA

010= STUCK_HI_SCL + STUCK_HI_SDA

171

172

173

MM_PROC_WAITING MM_SIGNAL_ERR

MM_MAX_WAIT_ERR

Not used	Memory Manager error traps.
Not used
Not used	MM debug = 0.

Operating Overview 2-25

www.GovTechMedia.com