HP ColorPro CAD manual Mechallpensbad Mechcarriagelatcherror Mechpumpjam

421

422

423

424

425

426

427

428

429

431

432

433

434

435

436

437

438

439

441

442

443

444

445

446

451

452

453

454

455

456

457

458

459

461

462

463

464

MECH_BAD_BLACK_PEN MECH_BAD_CYAN_PEN MECH_BAD_MAGENTA_PEN MECH_BAD_YELLOW_PEN MECH_BLACK_OOI MECH_CYAN_OOI

MECH_MAGENTA_OOI MECH_YELLOW_OOI MECH_UDV_PROB MECH_PEN_E_5_SHORT MECH_SS_FAILURE MECH_NO_RAMP_MEMORY MECH_BAD_SPIT_FREQ MECH_PEN_VP1_SHORT MECH_PEN_VP2_SHORT MECH_PEN_E_12_SHORT

MECH_ALL_PENS_BAD

MECH_CARRIAGE_LATCH_ERROR

MECH_PUMP_JAM

MECH_STALLED_MOTOR_ENCODER MECH_STALLED_MOTOR_EMF MECH_PAPER_ENCODER MECH_NUDGE_ERROR MECH_PAPER_JAM_ERROR MECH_PEN_SHORT_OVER MECH_DARWIN_OVERTEMP MECH_DARWIN_JR_OVERTEMP MECH_RESISTOR_TEST_FAIL MECH_SS_OUTOFLIMITS MECH_SS_DIRTYPON1 MECH_SS_DIRTYPON2 MECH_SS_DIRTYPON3 MECH_SS_DIRTYPON4 MECH_SHORT_TIMER MECH_SS_REHOMING_ERROR MECH_SPIT_POSITION_ERROR MECH PAPERMOTOR NO INDEX

Not used – pen/ flexcable/ Carriage PCA/ Logic PCA error	Black pen had bad ID or TSR.
Not used – pen/ flexcable/ Carriage PCA/ Logic PCA error	Cyan pen had bad ID or TSR.
Not used – pen/ flexcable/ Carriage PCA/ Logic PCA error	Magenta pen had bad ID TSR.
Not used – pen/ flexcable/ Carriage PCA/ Logic PCA error	Yellow pen had bad ID TSR.
Not used – ISS/ Harness/ Logic PCA error	Black out of ink trap.
Not used – ISS/ Harness/ Logic PCA error	Cyan out of ink trap.
Not used – ISS/ Harness/ Logic PCA error	Magenta out of ink trap.
Not used – ISS/ Harness/ Logic PCA error	Yellow out of ink trap.
Not used	12V supply was out of spec (was 424).
Pen failed	Electrical short test on 5 V failed.
Service Station/ harness / Logic PCA error	SS jammed or SS OPTO failure.
Not used	Downloadable ramp allocation memory failed.
Not used - Logic PCA/ bad pen	Spit Frequency or Spit Count out of range.
Pen / Logic PCA/ carriage base/ Flexcable connection error	Electrical short test on VP1 failed.
Pen / Logic PCA/ carriage base/ Flexcable connection error	Electrical short test on VP2 failed.
Pen / Logic PCA/ carriage base/ Flexcable connection error	Electrical short test on 12 V failed.
Not used – pen issue/ Logic PCA/ Carriage base	All 4 pens have a bad ID. This error could be caused
	By a short on one of the pens, which cannot be
	specifically identified.
Not used – Recoverable error	The carriage latch is open.
	This error should become something more
	benign.
ISS pump motor jam – ISS/ Logic PCA / Harness	Pump could not move to desired position.
Encoder wheel / Linefeed PCA / Logic PCA error	Motor stall: paper encoder signal.
Not used	Motor stall: EMF signal.
Encoder wheel / linefeed PCA / Logic PCA error	Thrown when quadrature calibration fails.
Not used	Nudge position error outside limits.
Not able to feed out media / Linefeed motor / Linefeed PCA error	Paper jam while ejecting.
Pen issue / Logic PCA / carriage base error	Pen Short Test failed (voltage increase).
Darwin Senior Failed – PCA	Darwin over temperature.
Darwin Junior Failed – PCA	Darwin Jr over temperature.
Not used - pen issue/ flex cable/ carriage base/ logic PCA	Resistor test > 100 nozzle failure.
Service Station / Logic PCA	SS could not be homed within reasonable limit.
Service Station / Logic PCA	SS could not be freed from carriage - case 1.
Service Station / Logic PCA	SS could not be freed from carriage - case 2.
Service Station / Logic PCA	SS could not be freed from carriage - case 3.
Service Station / Logic PCA	SS could not be freed from carriage - case 4.
Pen short detected – pen issue	The short test was not completed within required time.
Service Station/ Logic PCA	Error while rehoming service station.
Firmware error – Encoder strip / SS / carriage base/ Logic PCA	Error in spit position.
Not used	Thrown when index mark is not found.

Operating Overview 2-29

www.GovTechMedia.com