MIXER OPERATIONS (BASIC OPERATIONS)

MIXER OPERATIONS

BASIC OPERATIONS

1

POWER

2

7

 

3

MASTER

TRIM

LEVEL

4

 

HI, MID, LOW

 

 

8

 

BALANCE

5

 

6

 

1.Set rear panel POWER switch to ON.

2.Set the input selector switch for the desired channel to choose the connected component.

When using CD input or LINE input, the connection panel’s DIGITAL/CD switch or DIGITAL/LINE switch must be set to [CD] or [LINE].

When using a DIGITAL input, the connection panel’s DIGITAL/ CD switch or DIGITAL/LINE switch must be set to [DIGITAL].

3.Use the TRIM dial to adjust the input level.4.Use the channel equalizer dials (HI, MID, LOW) to adjust the tone.

5.Use the channel fader lever to adjust the sound volume of the selected channel.

6.To use the cross fader on the selected channel, set the CROSS FADER ASSIGN switch to either cross fader channel A or channel B, and operate the cross fader lever.

When not using the cross fader, set the CROSS FADER ASSIGN switch to [THRU].

7.Use the MASTER LEVEL dial to adjust the overall sound volume.8.Use the BALANCE dial to adjust the sound balance between right and left.

Microphone input

 

 

 

 

 

 

 

 

 

Booth monitor output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEREO/

MONO

Headphones output

Fader curve

[Selecting Stereo or Monaural]

When the STEREO/MONO switch is set to [MONO], the master output becomes a monaural combination of L+R channels.

[Microphone Input]1.To use a microphone, set the MIC switch to [ON] or [TALK OVER].

When the switch is set to [TALK OVER], any time a sound of over –15 dB is detected by the microphone, the output for all sound sources other than the microphone are attenuated by 20 dB.

2.Use the MIC 1 LEVEL dial to adjust the sound volume of MIC 1, and use the MIC 2 LEVEL dial to adjust the sound volume of MIC 2.

3.Use the microphone equalizer dials (HI, LOW) to adjust the tone of the microphone sound.

The microphone equalizer function operates simultaneously on microphone 1 and 2.

[Booth Monitor Output]

1.Set the connection panel’s MIC SIGNAL switch to select whether microphone sounds are output to the booth monitor.

When set to the [ADD] position, microphone sounds are output to the booth monitor, and when set to the [CUT] position, microphone sounds are not output to the booth monitor.

2.Use the BOOTH MONITOR dial to adjust the sound volume.

The BOOTH MONITOR dial can be used to adjust the sound volume independently of the MASTER LEVEL dial.

[Headphones Output]1.Use the CUE buttons (channels 1 to 4, MASTER, effector) to select the source.

The selected CUE button lights brightly.

2.Set the headphones (MONO SPLIT/STEREO) switch.

When set to the [MONO SPLIT] position, the left channel outputs the sound selected with the CUE button, while the right channel outputs the master audio (only when the CUE button for the [MASTER] is ON).

When set to the [STEREO] position, the sound corresponding to the selected CUE button is output in stereo.

3.When [MONO SPLIT] is selected, use the MIXING dial to adjust the balance of sound between the left channel (sound selected with the CUE button), and the right channel (the master sound – but only when the CUE button for the [MASTER] is ON).

When the MIXING dial is rotated clockwise (toward [MASTER]), the master output (only when the CUE button for the [MASTER] is ON) increases; when rotated counterclockwise (toward [CUE]), the sound selected with the CUE button is output.

4.Use the LEVEL dial to adjust the headphones’ sound volume.[Fader Curve Selection]

The sound volume response to fader operation can be set to one of three characteristic curves.

7Use the CH FADER switch to select the desired channel fader response curve.

At the left setting, the curve operates to produce a rapid rise as the channel fader approaches its distant position.

At the right setting, the curve operates to produce an even, neutral rise throughout the channel fader’s movement.

At the middle setting, an intermediate curve is produced, midway between the two curves noted above.

This setting applies equally to channels 1 to 4.

12

<DRB1394> En