Manuals / Brands / Computer Equipment / Modem / HP / Computer Equipment / Modem

HP NRM42 4.5.3 Firmware, Browse, Browse, Browse:, UPGRADE, UPGRADE, Warning, “Browse…”, “Upgrade”, New Firmware Location:

1 61

Download 61 pages, 5.13 Mb

4.5.3 Firmware

Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over time this software may be improved and modified, and your router allows you to upgrade the software it runs to take advantage of these changes.

To upgrade the firmware of router, you should download or copy the firmware to your local environment first. Press the “Browse…” butto n to specify the path of the firmware file. Then, click “Upgrade” to start upgrading. When the procedure is completed, router will reset automatically to make the new firmware work.

New Firmware Location: Type in the location of the file you want to upload in this field or click Browse to find it.

Browse: Click Browse... to find the .ras file you want to upload. Remember that you must decompress compressed (.zip) files before you can upload them.

UPGRADE: Click UPGRADE to begin the upload process. This process may take up to two minutes.

After two minutes, log in again and check your new firmware version in the System Status screen.

If the upload was not successful, the following screen will appear. Click Back to go back to the Firmware screen.

DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router.

Warning

50

Contents

Page INDEX 1.1 Introducing the ADSL2+ Router Page 1.2 Features of the ADSL2+ Router Firewall Domain Name System (DNS) relay Dynamic Domain Name System (DDNS) PPP over Ethernet (PPPoE): RIP1/2 Routing Simple Network Management Protocol (SNMP) Web based GUI Firmware Upgradeable Rich management interfaces 2.1 Important note for using the ADSL2+ Router 2.2 Package Contents 2.3 The Front LEDs ADSL2+ Router with 4-portSwitch 802.11g ADSL2+ Router model 2.4 The Rear Ports Port Meaning 2.5 Cabling 3.1 Before Configuration Configuring PC in Windows XP Configuring PC in Windows Configuring PC in Windows 98/Me Configuring PC in Windows NT4.0 3.2 Factory Default Settings 3.2.1 Username and Password 3.3 LAN and WAN Port Addresses 3.4 Information from your ISP 3.5 Configuring with your Web Browser Quick Start Interface Setup Advanced Setup Access Management Maintenance 4.1 Quick Start Step1 Step2: Step3: Page Step4: 4.2 Interface Setup 4.2.1 Internet VCI: ATM QoS: CBR UBR VBR Dynamic Route: RIP Version: RIP Direction: Multicast: 4.2.2 LAN Enable disabled Relay Starting IP Address: IP Pool Count: 4.2.3 for Wireless ADSL2+ Modem/router model only Broadcast SSID: Yes Channel ID: Authentication Type: 64-bit Active: Actived Action: Deny Association Allow Association 4.3 Advanced Setup 4.3.1 Routing Dest IP: Mask: Gateway IP: Metric: Device: 4.3.2 NAT Number of IPs: DMZ DMZ: Disabled: Enabled: Apply Virtual Server WAN Rule Index: Start Port Number: End Port Number: Local IP Address: IP Address Mapping Rule Type: Local Start IP: Local End IP: Public Start IP: Public End IP: Page 4.3.3 ADSL 4.4 Access Management 4.4.1 ACL 4.4.2 IP Filter Source IP Address: Subnet Mask: Source Port Number: 0 Destination IP Address: 4.4.3 SNMP 4.4.4 UPnP 4.4.5 DDNS 4.5 Maintenance 4.5.1 Administrator 4.5.2 Time Zone 4.5.3 Firmware 4.5.4 SysRestart 4.5.6 Diagnostics 4.6 Status 4.6.1 Device Info Connection Type: VPI/VCI: Subnet mask: Default Gateway: DNS Server: 4.6.2 System Log 4.6.3 Statistics Transmit total PDUs: Transmit total Error Counts: Receive total PDUs: Receive total Error Counts: Problem Corrective Action None of the LEDs are on when you turn on the router You have forgotten your router login and/or password Initialization of the Frequent loss of ADSL linesync (disconnections) Can’t ping any PCs on the LAN