INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL
1.Install wheel axle (6) through wheel carriage (63) and install wheels
(5)onto wheel axle (6) with spacers (64) as shown. Secure wheel bracket as shown, a deep socket is recommended.
IMPORTANT! DO NOT OVER TIGHTEN.
2.Mark pole sections with tape as shown.
3.IMPORTANT! Center alignment slot of middle pole section (2) in a lower hole of top pole section (1) as shown. While maintaining alignment, bounce pole top (1) and middle section (2) together as shown until they no longer move toward taped reference mark. Upright assembly. NOTE: Pole sections should have a
4.IMPORTANT! Center alignment slot of lower pole section (3) in a lower hole of middle pole section (2) as in step 3. While maintaining alignment, bounce assembly and lower section (3) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a
5.Install rod (7) through holes in bottom pole section (3) and eyebolt (8).
6.Insert pole assembly into tank assembly as shown. Secure pole assembly with upper pivot bracket (9) and lock nut (10). IMPORTANT! Two people recommended for this step.
7.Secure base struts (11) to pole using bolt (12) washers (13) and nut
(15)as shown.
WARNING: TIGHTEN BOLT (12) IN LOCK NUT (15) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE.
Rotate the
8.Secure base struts (11) to base using bolt (16) washers (13) and nut (14).
9.Insert carriage bolts (18) into middle set of holes on wheel bracket (21) as shown. Attach lower pivot bracket (17) to wheel bracket using bolt (18), washers (13), disc (28), and nut (10) as shown. Tighten completely.
10.Attach handle bar (20) to wheel bracket assembly using nuts (14) as shown.
11.Install wheels (3) onto axle (24) and wheel bracket assembly with push caps (25) as shown.
12.Attach wheel bracket assembly to base assembly using bolt (19), washers (13), and nut (10) as shown.
13.Carefully reposition entire assembly as shown.
14.Attach front of plastic handle (26) to back of plastic handle (23) around handle bar (20) using self- tapping screws (27) as shown. IMPORTANT! Front of plastic handle (26) should face outward, away from pole assembly.
15.Insert bolts (66) through plastic handle assembly, handle bar (20), and attach nuts (14) as shown. Tighten completely. IMPORTANT! Two people recommended for this step.
16.Install pole mount bracket (53) with carriage bolts (54) as shown. Tighten flange nuts (14) completely.
17.Attach spacers (55, 56) to pole mount bracket (53) with bolts (33), washers (57), and nuts (34) as shown. IMPORTANT! Tighten until washers (57) no longer move.
18.Attach covers (58) onto pole mount bracket (53) with carriage bolt (39) and nut (14) as shown. IMPORTANT! Loop end of pin lanyard (59) over carriage bolt (39) during this assembly.
NOTE: Assemble lanyard (27) to locking pin (28) as shown.
19.Apply logo and height indicator labels (52) to adjustment rod (51) as shown. Attach handle parts (48, 49) to adjustment rod (51) with screw (50), carriage bolts (22), and flange nuts (14) as shown. NOTE: Holes in adjustment rod allow for either rear access or side access.
20.Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with
pin (60).
21.Attach backboard support brackets (29) to the backboard frame using bolts (33), spacers (30), and nuts (34) as shown.
22.Attach lower elevator tubes (35) and spring (42) to backboard support brackets (29) using spacers (32), bolt (36), and nut (38) as shown. NOTE: Rim mounting nuts and bolts (31) supplied with rim hardware.
23.Attach upper elevator tubes (40) to backboard support
brackets (29) using spacers (32), bolt (36), and nut (38) as shown.
24.Support pole on sawhorse. Attach backboard assembly to top pole section (1). Install pole cap (41).
IMPORTANT! Two people recommended for this step. Use caution; elevator assembly is heavy.
25.Install handle assembly to lower elevator tubes (35) using
bolt (36), spacers (37) and nut (38). NOTE: Before going onto the next step, set adjustment system to the 10’ (3.05m) setting.
26.Insert bolt (36) through the left side upper elevator tube (40), then stretch spring (42) onto bolt (36). Insert bolt (36) through the right side upper elevator tube (40) and secure with nut (38).
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
27.Roll completed assembly to desired playing area. Secure assembly
to ground using
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY TIP OVER.
28.While holding handle, remove pin (60).
29.Move elevator up or down to desired height.
30.Replace pin full length to lock system at desired height.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
31.Apply height and moving label (47) to front of pole as shown.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY.
32.Install net clips as shown. (See illustration)
33.Install net as shown. (See illustration)
P/N 214949A | 01/03 | 4 |
