INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL
1.Mark pole sections with tape as shown.
2.IMPORTANT! Bounce pole top (1) and middle section (2) together as shown until they no longer move toward taped reference mark. Upright assembly. NOTE: Pole sections should have a
3.IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST align to correctly position elevator system toward playing surface. Add bottom pole section (3) to assembly as shown and bounce until completely tight. NOTE: Pole sections should have a
4.Install wheels (17) onto axle (28) and wheel bracket (25) with push caps (29) as shown.
5.Position base as shown. Secure wheel bracket assembly with bolt (16) and nut
(15)as shown.
6.Install rod (4) through holes in bottom pole section (3) and eyebolt (5).
Insert pole assembly into tank (6) and through center hole on wheel assembly as shown. Secure pole assembly with lock nut (8). NOTE: Two people recommended for this step.
7.Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as shown. Rotate the
8.Secure base struts (9) to base using bolt (14) washers (11) and nut (15).
9.Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut
(8)as shown.
10.Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured during step 12. Carefully place base assembly on its side. Install lower pivot bracket (22) with bolt (23), washers (20) and lock nut (8) as shown.
11.Secure both hinge tubes (24) to second wheel bracket (25) with carriage bolts (26) and flange nuts (15).
12.Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown.
13.Position base as shown. Secure wheel bracket assembly with disc (30), washer
(20)and nut (8) as shown. NOTE: Two people recommended for this step.
14.Carefully reposition entire assembly as shown. IMPORTANT! Two people recommended for this step.
15.Snap tinnerman nut (31) onto inner channel (32). Place inner channel into outer channel (33) as shown.
16.Slide handle (34) into position as shown and secure with bolts (35), washers (11), and nuts (15). Tighten completely.
17.Install bolt (36), washers (11), and nut (37) as shown. Tighten until washers (11) are no longer loose. NOTE: Do not over tighten. Assemble trigger (38) to handle assembly (34, 32, 31) as shown and secure with bolt (39) and washer (11). Tighten completely.
18.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. Install trigger return spring (40) to handle assembly (32, 33) as shown.
19.Attach Accuheight label (41) to outer channel (33).
20.Attach spring (44) to pins (43) and install pins (43) onto pole mount bracket (45). Attach other spring (44) to opposite side. NOTE: Gently enlarge eyelets of spring with pliers if springs do not fit over pins.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
21.Install pole mount assembly and reinforcement bracket (47) with carriage bolts (46) to pole as shown. Tighten flange nuts (15) completely.
22.Push back sliding pin (43) as shown in Figure A to fit adjustable system assembly through pole mount assembly. Then attach spring covers (48 & 49) onto pole mount bracket (45) with bolt (50), and nut (15) as shown in Figure B.
23.Install spacers (51) onto backboard brackets (52) with bolts (53, 54) and lock nuts (55, 37) as shown.
24.Assemble lower elevator tubes (56) as shown. NOTE : Tighten bolt (57) in lock nut
(58)until flush (even) with lock nut’s outer edge. IMPORTANT! It is necessary for all parts to be installed for this mechanism to work safely and properly. NOTE: Test fit bolts into holes of brackets (52) and carefully rock them in a circular motion to ream out paint from holes if necessary
25.Starting with nuts (15) flush against board bracket (52), bolt red bracket (61) to board using bolts (60), washers (20), and foam pad (62) as shown. Do not tighten. Tightening will take place in step 30. NOTE: Place two bolts (60) through UPPER holes of red bracket only, as shown. Bend board brackets
(52)to line up with holes in backboard and secure using weld studs (73), and nuts (15) as shown.
26.Assemble upper elevator tubes (63) to backboard brackets (52) as shown. NOTE: Tighten bolt (57) in locknut (58) until flush (even) with locknut’s outer edge.
27.Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Then install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy.
28.Install upper elevator tubes (63) to triangle plates (66) as shown.
Next, install handle assembly (32, 33) to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as shown. NOTE: Tighten bolt (57) in locknut
(58)until flush (even) with locknut’s outer edge. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting.
29.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. Insert bolt (57) through left side upper elevator tube (63), then stretch springs
(68)onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58).
30.Install carriage bolt (69) through rim (70), washers (71) and (20) as shown. Tighten nut (72) completely. Place nut (8) about
31.Insert inner bracket (74) into bracket (61) as shown. Insert bolts (60) through washers (20) and through UPPER holes of inner (black) bracket (74) as shown. Tighten nuts (15) completely. Tighten all hardware from step 24 at this time.
32.Insert spacer (75) through rim assembly (70). Place rim assembly on bracket
(61)so that bolt (69) is inserted through hole on top of inner bracket (74).
33.Install bolt (76), through washers (20) and through top holes on side of bracket (61) and secure with nut (73) as shown. Tighten completely.
34.Install spring (77), concave washer (78) and center lock nut (37) to bolt (69) as shown.
NOTE: Do not over tighten as rim will not flex properly. See leveling instructions to determine how much to tighten nuts (8) and (37).
35.Place level on rim (70) and adjust nut (8) until level. Tighten nut (37) to set rim tension for playing.
36.Apply logo label (79) to cover plate (80) and install cover plate (80) on rim
(70)using self tapping screws (81) as shown. NOTE ORIENTATION OF
COVER PLATE.
37.Secure net (82) to rim (70).
38.Attach front cover (83) to hinge tubes (24) using carriage bolts (84) and flange nuts (15) as shown.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY TIP OVER.
39.Apply height and moving label (85) to front of pole as shown.
40.Roll completed assembly to desired playing area. Secure assembly to ground using rope (86) and tie down stake (7). Fill tank with 34 gallons of water.
IMPORTANT! Add two gallons (7.6 Liters) of
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
41.Grasp handle and depress lever.
42.Push toward pole while holding lever. Raise or lower lever to desired height while pushing forward on handle.
43.Release handle making sure that horizontal pin (43) is locked into slot.
P/N 211606A 03/02 | 6 | printed on recycled paper |
