Manuals / Humminbird / Computer Equipment / Laminator

Humminbird LCR4 ID manual Transducer Mounting Procedure, Transducer Mounting Options

Models: LCR4 ID

1 39

Page 3

TRANSDUCER MOUNTING PROCEDURE

Humminbird’s high-speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum.

Please carefully consider the following before installing your transducer.

TRANSDUCER MOUNTING OPTIONS

A. Transom Mount- The Humminbird high speed transducer allows the transducer

Page 3

Image 3

Humminbird LCR4 ID manual Transducer Mounting Procedure, Transducer Mounting Options

Contents

Page TABLE OF CONTENTS TRANSDUCER MOUNTING OPTIONS TRANSDUCER MOUNTING PROCEDURE1. TRANSOM MOUNTING PROCEDURE Step Step StepStep Step Step3. Put approximately one inch of water in the bottom of the boat 2. INSIDE HULL MOUNTING PROCEDUREStep StepCAUTIONS INSTALLING THE LCR OTHER MOUNTING OPTIONS INSTALLING THE CABLESPage INSTALLATION TEST THE INSTALLATIONTEST THE INSTALLATION THEORY OF OPERATION USING THE LCRINTRODUCTION INTRODUCTIONUSING THE LCR INTRODUCTIONThe reading at the far right hand position of the display illustrates that which is being passed over at that time. If you are familiar with a flasher unit, you might think of the information coming on the right side of the screen as the information that would be seen at one instant on a flasher see Figure 1. However, unlike a flasher, this information is not lost but it is shifted or moved to the left as new information comes on. Therefore, the information is retained until it disappears from the left hand position of the display USING THE LCR INTRODUCTION1. Objects at least three inches off the bottom are displayed in red. The bottom and structure attached to the bottom are displayed in black. The electronics in the LCR4-lDand LCR40-ID can separate the bottom from objects at least three inches off the bottom no matter what depth range you are viewing. This means that fish close to the bottom will be easily seen on the LCR see Figure 2. These same fish would be missed on an ordinary display because they would just look like part of the bottom What is Total Screen Update? TOTAL SCREEN UPDATETOTAL SCREEN UPDATE USING THE LCROPERATIONAL INSTRUCTIONS OPERATIONAL INSTRUCTIONSUSING THE LCR USING THE LCR Please read the Theory of Operation in the front of the manual for a detailed explanation of the ID feature. Below are some tips to help you use this advanced ID featureOPERATIONAL INSTRUCTIONS USING THE LCR OPERATIONAL INSTRUCTIONS4. Automatic or Manual Mode What Zoom Does USING THE LCRHow To Use Zoom OPERATIONAL INSTRUCTIONSBottom Lock USING THE LCROPERATIONAL INSTRUCTIONS Some Additional Things You Should Know About ZoomOPERATIONAL INSTRUCTIONS USING THE LCRFish Alarm Bottom AlarmUSING THE LCR Automatic Mode In the automatic mode a continuous alarm will sound only when the bottom depth is equal to or less than the alarm setting. Fish entering the alarm range will not trigger the alarm unless of course the fish alarm is onOPERATIONAL INSTRUCTIONS Reading will not be seen while in the manual mode Optional Surface Temperature Gauge or Trolling Speed IndicatorUSING THE LCR OPERATIONAL INSTRUCTIONSSome additional things you should know about the LCR ADDITIONAL INFORMATIONSimulator USING THE LCRCARING FOR YOUR LCR USING THE LCRADDITIONAL INFORMATION LEARNING TO USE YOUR LCR LEARNING TO USE YOUR LCRUSING THE LCR USING THE LCR LEARNING TO USE YOUR LCRPush the Auto On/Off button to go back to the automatic mode USING THE LCR Press the Fish Alarm on/off button. Notice the indicator in the lower part of the screen indicating the Fish Alarm is on. Now if an object is detected between the surface and the bottom, a short alarm sound will be heard. By pressing the Fish Alarm on/off button again the Fish Alarm is turned offLEARNING TO USE YOUR LCR LEARNING TO READ THE DISPLAY LEARNING TO READ THE DISPLAYUSING THE LCR USING THE LCR LEARNING TO READ THE DISPLAYBrush or thick standing timber will appear as a thick mass with holes or gaps as shown above. Notice how the strong fish returns red dots with black behind can be easily distinguished MAINTENANCE AND WARRANTY MAINTENANCEMAINTENANCE 2. There is no transducer detected TROUBLESHOOTINGTROUBLESHOOTING 1. Nothing happens when I turn the unit on3. There is no bottom reading visible on the display MAINTENANCE AND WARRANTYTROUBLESHOOTING 8. The screen begins to fadeout. Images are not as sharp as normal 5. The unit comes on before I press POWER, and wont turn off7. My unit loses power at high speeds 6. I get gaps in the reading at high speedsWARRANTY HUMMINBIRD ONE YEAR FULL WARRANTYMAINTENANCE AND WARRANTY SERVICE POLICY SERVICE POLICYMAINTENANCE AND WARRANTY Humminbird Service Department Three Humminbird Lane Eufaula, AL USA CUSTOMER SUPPORTCUSTOMER SUPPORT MAINTENANCE AND WARRANTY