FUEL HANDLING

Fuel

CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

 

!

WARNING! Always ensure there is

 

adequate ventilation when handling fuel.

 

 

 

Petrol

•Use good quality unleaded or leaded petrol.

•CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures. Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

•The lowest recommended octane grade is 90 (RON). If you run the engine on a lower octane grade than 90 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel, either Aspen two-stroke fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburettor adjustment may be necessary when changing the type of fuel (see the instructions under the heading Carburettor).

Running-in

Avoid running at a too high speed during the first 10 hours.

Two-stroke oil

•For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two-stroke engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

•A poor oil quality and/or too high oil/fuel ratio may jeopardise function and decrease the life time of catalytic converters.

Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB formulated for air-cooled, two-stroke engines.

Petrol, litre

Two-stroke oil, litre

 

 

 

 

2% (1:50)

3% (1:33)

 

 

 

5

0,10

0,15

 

 

 

10

0,20

0,30

 

 

 

15

0,30

0,45

 

 

 

20

0,40

0,60

 

 

 

Mixing

•Always mix the petrol and oil in a clean container intended for fuel.

•Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

•We recommend the use of special oil (chain oil) with good adhesion characteristics.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

•In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your service agent when choosing chain oil.

English – 17

Page 16 Page 18
Page 17
Image 17
Husqvarna 1153176-26 manual Fuel Handling
Page 16 Page 18

1153176-26 specifications

The Husqvarna 1153176-26 is a reliable and innovative addition to the lawn care equipment market, designed specifically to meet the needs of both homeowners and professional landscapers. This product is a hedge trimmer that combines power, precision, and user-friendly features, making it an essential tool for maintaining gardens, hedges, and shrubs.

One of the key features of the Husqvarna 1153176-26 is its robust engine. It is powered by a high-performance, low-emission engine that delivers the power needed for efficient cutting while minimizing environmental impact. This focus on eco-friendliness is a significant technological advancement, setting Husqvarna apart in the competitive outdoor power equipment landscape.

The trimmer is equipped with long, dual-action blades that enhance cutting efficiency and offer improved cutting performance. The length of the blades enables users to tackle larger areas quickly, while the dual-action design reduces vibration, ensuring smoother operation and greater comfort during extended use. This design also contributes to achieving a cleaner cut, which is essential for the health of the plants being trimmed.

Another defining feature of the Husqvarna 1153176-26 is its ergonomic design. The handle is designed to provide comfort and ease of use, allowing operators to maneuver the trimmer with minimal fatigue. Additionally, the soft-grip handles ensure a secure hold, even in challenging conditions.

Safety is paramount in the design of the Husqvarna 1153176-26. The trimmer is equipped with safety features, including a safety lockout system that prevents accidental starts. This ensures that users can work without the constant worry of unintended activation, making it a safe choice for professionals and amateurs alike.

Portability and convenience are also significant considerations in the Husqvarna 1153176-26 design. The lightweight construction makes it easy to transport and operate, while the well-balanced design reduces strain on the arms and shoulders during use.

In summary, the Husqvarna 1153176-26 stands out as a high-quality hedge trimmer, blending power, efficiency, and safety in a user-friendly package. Its advanced engine technology, effective cutting blades, ergonomic design, and focus on safety make it an ideal choice for anyone looking to maintain their landscaping with precision and ease. With this equipment, users can achieve professional results while ensuring their outdoor spaces remain in pristine condition.
Top Page Image Contents