Manuals / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 1153181-26 manual EC-declaration of conformity, Applies to Europe only, Technical Data

Models: 1153181-26

1 44

Download 44 pages 53.45 Kb

Page 43

EC-declaration of conformity

TECHNICAL DATA

EC-declaration of conformity

(Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the chain saws for forest service Husqvarna 570, 576 XP and 576 XPG from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the requirements of the COUNCIL’S DIRECTIVES:

-of May 17, 2006 "relating to machinery" 2006/42/EC

-of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:

EN ISO 12100-2:2003, CISPR 12:2001, EN ISO 11681-1:2004

Notiﬁed body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out EC type examination in accordance with the machinery directive’s (2006/42/EC) article 12, point 3b. The certiﬁcates for EC type examination in accordance with annex IX, have the numbers: 0404/09/2084

In addition, SMP, Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has certiﬁed conformity with annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certiﬁcates have the numbers: 01/161/055

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna December 29, 2009

Bengt Frögelius, Development director chainsaw R&D

(Authorized representative for Husqvarna AB and responsible for technical documentation.)

English – 43

Image 43

Husqvarna 1153181-26 manual EC-declaration of conformity, Applies to Europe only, EN ISO 12100-22003, CISPR 122001, EN ISO

Contents

Operator′s manual 570 576 XP 576 XPGEnglish Symbols on the machine KEY TO SYMBOLSSymbols in the operator’s manual CONTENTS CONTENTSContents KEY TO SYMBOLSDear Customer INTRODUCTIONWhat is what on the chain saw? WHAT IS WHAT?health risk GENERAL SAFETY PRECAUTIONSBefore using a new chain saw WARNING! The inside of the mufﬂer ! contain chemicals that may bePersonal protective equipment Machine′s safety equipmentWARNING! Most chain saw accidents ! happen when the chain touches the Always use common senseThe brake is applied when the front hand guard B is pushed forwards GENERAL SAFETY PRECAUTIONSGENERAL SAFETY PRECAUTIONS Will my hand always activate the chain brake during a kickback?Throttle lockout Chain catcherMufﬂer Stop switchRight hand guard Vibration damping systemChain Cutting equipmentGeneral rules Cutting equipment designed to reduce kickbackincreases the risk of kickback Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth WARNING! Departure from the sharpening instructions considerablySharpening cutting teeth General advice on adjusting depth gauge settingincreased if the depth gauge setting is Adjustment of depth gauge settingand cause serious or even fatal injury Tensioning the chainLubricating cutting equipment WARNING! A slack chain may jump offChecking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubricationGENERAL SAFETY PRECAUTIONS happen when the chain touches the operatorAvoid situations where there is a risk of WARNING! Most chain saw accidentsWARNING! Always wear gloves, when ASSEMBLYFitting the bar and chain Fitting a spike bumperPetrol adequate ventilation when handling fuelFUEL HANDLING FuelChain oil Fuel safetyprecautions, will lessen the risk of ﬁre FuellingLong-term storage Transport and storageFUEL HANDLING Warm engine STARTING AND STOPPINGStarting and stopping Cold engineSTARTING AND STOPPING Stoppinghealth risk General working instructions Basic safety rulesWORKING TECHNIQUES Before useWORKING TECHNIQUES jam. Always stop the engine before cleaningGeneral rules WORKING TECHNIQUES Basic cutting techniqueGeneral TermsThe log is supported at one end. There is a high risk Tree felling techniqueLimbing Cutting WARNING! Never attempt to cut logswith a diameter larger than the bar length of your saw Felling directionClearing the trunk and preparing your retreat FellingWORKING TECHNIQUES Felling cutCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a ”trapped tree”Cutting the trunk into logs How to avoid kickbackWhat is kickback? Limbing WARNING! A majority of kickbackFine adjustment MAINTENANCECarburettor adjustment Basic settings and running inChecking brake band wear Checking, maintaining and servicing chain saw safety equipmentCorrectly adjusted carburettor High speed jet Himmediately When the bar hits the stump the brake should be appliedChecking the inertia brake release Checking the brake triggerChain catcher MufﬂerMAINTENANCE Stop switchTensioning the recoil spring WARNING! When the recoil spring isStarter Changing a broken or worn starter cordmust always be replaced Air ﬁlterSpark plug Lubricating the bar tip sprocketNeedle bearing lubrication Adjustment of the oil pump”Air Injection” centrifugal cleaning running when making adjustmentsFitting the winterising kit Temperature 0C or colderTemperature -5C or colder Winter useMAINTENANCE Heated handlesElectrical carburettor heating 576 XPGMonthly maintenance Maintenance scheduleDaily maintenance Weekly maintenance576 XP TECHNICAL DATATechnical data WeightPitch, inch Bar and chain combinationsSaw chain ﬁling and ﬁle gauges Length, inchTECHNICAL DATA EC-declaration of conformityApplies to Europe only EN ISO 12100-22003, CISPR 122001, EN ISO´z+U2,¶66¨ ´z+U2,¶66¨ 1153181-26Original instructions