Manuals / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 1153181-26 Contents, Key To Symbols, Introduction, What Is What?, Assembly, Maintenance

Models: 1153181-26

1 44

Download 44 pages 53.45 Kb

Page 3

CONTENTS

CONTENTS

Contents
KEY TO SYMBOLS
Symbols on the machine:	2
Symbols in the operator’s manual:	2
CONTENTS
Contents	3
INTRODUCTION
Dear Customer,	4
WHAT IS WHAT?
What is what on the chain saw?	5
GENERAL SAFETY PRECAUTIONS
Before using a new chain saw	6
Important	6
Always use common sense	7
Personal protective equipment	7
Machine′s safety equipment	7
Cutting equipment	11
ASSEMBLY
Fitting the bar and chain	17
FUEL HANDLING
Fuel	18
Fuelling	19
Fuel safety	19
STARTING AND STOPPING
Starting and stopping	21
WORKING TECHNIQUES
Before use:	23
General working instructions	23
How to avoid kickback	30
MAINTENANCE
General	31
Carburettor adjustment	31
Checking, maintaining and servicing chain saw
safety equipment	32
Mufﬂer	34
Starter	35
Air ﬁlter	36
Spark plug	36
Lubricating the bar tip sprocket	36
Needle bearing lubrication	37
Adjustment of the oil pump	37
Cooling system	37
”Air Injection” centrifugal cleaning	37
Winter use	38
Heated handles	39
Maintenance schedule	40
TECHNICAL DATA
Technical data	41
Bar and chain combinations	42
Saw chain ﬁling and ﬁle gauges	42
EC-declaration of conformity	43

English – 3

Image 3

Husqvarna 1153181-26 manual Contents, Key To Symbols, Introduction, What Is What?, General Safety Precautions, Assembly

Contents

570 576 XP 576 XPG Operator′s manualEnglish KEY TO SYMBOLS Symbols on the machineSymbols in the operator’s manual CONTENTS CONTENTSContents KEY TO SYMBOLSDear Customer INTRODUCTIONWhat is what on the chain saw? WHAT IS WHAT?health risk GENERAL SAFETY PRECAUTIONSBefore using a new chain saw WARNING! The inside of the mufﬂer ! contain chemicals that may bePersonal protective equipment Machine′s safety equipmentWARNING! Most chain saw accidents ! happen when the chain touches the Always use common senseThe brake is applied when the front hand guard B is pushed forwards GENERAL SAFETY PRECAUTIONSGENERAL SAFETY PRECAUTIONS Will my hand always activate the chain brake during a kickback?Throttle lockout Chain catcherMufﬂer Stop switchRight hand guard Vibration damping systemChain Cutting equipmentGeneral rules Cutting equipment designed to reduce kickbackincreases the risk of kickback Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth WARNING! Departure from the sharpening instructions considerablySharpening cutting teeth General advice on adjusting depth gauge settingincreased if the depth gauge setting is Adjustment of depth gauge settingand cause serious or even fatal injury Tensioning the chainLubricating cutting equipment WARNING! A slack chain may jump offChecking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubricationGENERAL SAFETY PRECAUTIONS happen when the chain touches the operatorAvoid situations where there is a risk of WARNING! Most chain saw accidentsWARNING! Always wear gloves, when ASSEMBLYFitting the bar and chain Fitting a spike bumperPetrol adequate ventilation when handling fuelFUEL HANDLING FuelChain oil Fuel safetyprecautions, will lessen the risk of ﬁre FuellingTransport and storage Long-term storageFUEL HANDLING Warm engine STARTING AND STOPPINGStarting and stopping Cold engineStopping STARTING AND STOPPINGhealth risk General working instructions Basic safety rulesWORKING TECHNIQUES Before usejam. Always stop the engine before cleaning WORKING TECHNIQUESGeneral rules WORKING TECHNIQUES Basic cutting techniqueGeneral TermsThe log is supported at one end. There is a high risk Tree felling techniqueLimbing Cutting WARNING! Never attempt to cut logswith a diameter larger than the bar length of your saw Felling directionClearing the trunk and preparing your retreat FellingWORKING TECHNIQUES Felling cutCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a ”trapped tree”Cutting the trunk into logs How to avoid kickbackWhat is kickback? Limbing WARNING! A majority of kickbackFine adjustment MAINTENANCECarburettor adjustment Basic settings and running inChecking brake band wear Checking, maintaining and servicing chain saw safety equipmentCorrectly adjusted carburettor High speed jet Himmediately When the bar hits the stump the brake should be appliedChecking the inertia brake release Checking the brake triggerChain catcher MufﬂerMAINTENANCE Stop switchTensioning the recoil spring WARNING! When the recoil spring isStarter Changing a broken or worn starter cordmust always be replaced Air ﬁlterSpark plug Lubricating the bar tip sprocketNeedle bearing lubrication Adjustment of the oil pump”Air Injection” centrifugal cleaning running when making adjustmentsFitting the winterising kit Temperature 0C or colderTemperature -5C or colder Winter useMAINTENANCE Heated handlesElectrical carburettor heating 576 XPGMonthly maintenance Maintenance scheduleDaily maintenance Weekly maintenance576 XP TECHNICAL DATATechnical data WeightPitch, inch Bar and chain combinationsSaw chain ﬁling and ﬁle gauges Length, inchTECHNICAL DATA EC-declaration of conformityApplies to Europe only EN ISO 12100-22003, CISPR 122001, EN ISO1153181-26 ´z+U2,¶66¨ ´z+U2,¶66¨Original instructions