Manuals / Husqvarna / Lawn and Garden / Brush Cutter

Husqvarna 327LDX-series Assembling the cutting equipment, Assembly, WARNING! Never use a cutting

Models: 327LDX-series

1 36

Download 36 pages 46.21 Kb

Page 11

Assembling the cutting equipment

ASSEMBLY

Assembling the cutting equipment

WARNING!

! When ﬁtting the cutting attachment it is extremely important that the raised section on the drive disc/support ﬂange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is ﬁtted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting

! attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is ﬁtted this can cause serious personal injury.

Fitting the trimmer guard and trimmer head

•Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the ﬁtting on the shaft and secure with the bolt (L).

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

•To dismantle, follow the instructions in the reverse order.

English – 11

Image 11

Husqvarna 327LDX-series manual Assembling the cutting equipment, Fitting the trimmer guard and trimmer head, Assembly

Contents

Operator′s manual English327LDX-series ensure, while working, that no KEY TO SYMBOLSSymbols The operator of the machine mustCONTENTS CONTENTSContents KEY TO SYMBOLSDear Customer INTRODUCTIONWhat is what? WHAT IS WHAT?WARNING! The ignition system of this GENERAL SAFETY PRECAUTIONSWARNING! Listen out for warning signals Personal protective equipmentGENERAL SAFETY PRECAUTIONS Machine′s safety equipmentThrottle lockout WARNING! Never use a machine withMufﬂer Stop switchCutting attachment guard Vibration damping systemWARNING! Mufﬂers ﬁtted with catalytic WARNING! A faulty cutting attachmentCutting equipment Trimmer headAssembling and dismantling the two-pieceshaft ASSEMBLYAssembly Fitting the loop handleWARNING! Never use a cutting Assembling the cutting equipmentFitting the trimmer guard and trimmer head ASSEMBLYFuel Fuel safetyWARNING! Take care when handling fuel FUEL HANDLINGWARNING! The catalytic converter precautions, will lessen the risk of ﬁreFuelling MixingStarting and stopping WARNING! When the engine is startedSTARTING AND STOPPING Check before startingSTARTING AND STOPPING StoppingWARNING! Neither the operator of the Basic safety rulesWORKING TECHNIQUES General working instructionsTrimming Basic working techniquesGrass trimming with a trimmer head WARNING! Sometimes branches orCarburettor MAINTENANCEBasic setting Fine adjustmentHigh speed jet H Fine adjustment of the idle speed TCorrectly adjusted carburettor Low speed jet LMAINTENANCE MufﬂerCooling system Spark plugOiling the air ﬁlter Cleaning the air ﬁlterTwo-pieceshaft Air ﬁlterMAINTENANCE Bevel gearDaily Maintenance scheduleMaintenance maintenance327LDx TECHNICAL DATATechnical data WeightAttachments Approved accessoriesType Cutting attachment guard, Art. noPage 2,4-2,7 mm 8,5 m 28 10 cm 4,2 mClic 15 cm4,25 m 2,4-2,7mm095-.106 4,25 mClic T35, T35x8,5 m 28 10 cm 4,3 m 15 cm2,0-2,4 mm 6,0 m 18 10 cm 3,05 m15 cm ClicPage Page Page Page Page 1151209-26 ´z+S4 ¶6 ¨ ´z+S4 ¶6 ¨