Manuals / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 338XPT EPA III, 1151375-95 manual Muffler, Starter, Changing a broken or worn starter cord

Models: 1151375-95 338XPT EPA III

1 44
Download 44 pages 46.37 Kb
Page 32
Image 32

MAINTENANCE

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week. This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage.

Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor screen is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

A muffler equipped with a catalytic converter significantly reduces the amount of hydrocarbons (HC), nitrogen oxides (NO) and aldehydes in the exhaust fumes. Carbon monoxide (CO), which is poisonous and odorless, is not however reduced! Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

Starter

WARNING! When the recoil spring is

! wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

32 – English

Page 31 Page 33
Page 32
Image 32
Husqvarna 338XPT EPA III, 1151375-95 manual Muffler, Starter, Changing a broken or worn starter cord
Page 31 Page 33

1151375-95, 338XPT EPA III specifications

The Husqvarna 338XPT is a powerful chainsaw designed specifically for professionals who require reliability and performance in demanding environments. One of its standout features is the lightweight design, making it easy to maneuver while still delivering impressive power. Weighing in at just over 10 pounds, the 338XPT allows users to work for extended periods without fatigue, making it an ideal choice for arborists and forestry workers.

At the heart of the Husqvarna 338XPT is its efficient engine, which not only provides robust cutting performance but is also designed with EPA III compliance in mind. This means the machine adheres to strict environmental regulations, producing lower emissions while ensuring a high power output. The X-Torq engine technology is one of the key innovations that contribute to its efficiency. This technology reduces fuel consumption by up to 20% while also decreasing harmful exhaust emissions. This dual benefit makes the 338XPT a viable option for users who prioritize both performance and environmental responsibility.

Another notable characteristic of the Husqvarna 338XPT is its advanced air filtration system, which enhances the durability of the engine by ensuring that only clean air reaches it. The centrifuge air cleaning system significantly prolongs the time between filter cleanings, allowing users to focus more on their work and less on maintenance. This feature is particularly beneficial in dusty or dirty job sites, ensuring optimal performance in various conditions.

Comfort and usability are also central to the design of the 338XPT. The chainsaw includes an ergonomic handle that allows for better control during operation, reducing vibrations and enhancing user comfort. Additionally, the chainsaw's easy-access chain tensioning system makes adjusting the chain as simple as possible, ensuring that users can quickly get back to their tasks at hand without unnecessary delays.

For safety-conscious users, the Husqvarna 338XPT is equipped with features like a combined choke/stop control that allows for easy starting and reduces the risk of engine flooding. Furthermore, the chainsaw's inherent balance and lightweight structure contribute to safer handling and operation.

In summary, the Husqvarna 338XPT EPA III is a top-of-the-line chainsaw that combines power, efficiency, and user-friendly features, making it a prime choice for professionals in the forestry and arborist fields. Its robust engine technology, advanced air filtration, and ergonomic design ensure that you can tackle any job with confidence and ease.