Husqvarna manual Technical Data, 357XP 359, Recommended original and replacement

TECHNICAL DATA

	357XP	359
Engine
Cylinder volume, cu.in/cm3	3,5/57	3,6/59
Cylinder bore, inch/mm	1,81/46	1,85/47
Stroke, inch/mm	1,34/34	1,34/34
Idle speed, rpm	2 700	2 700
Power, kW/ rpm	3,2/ 9 600	2,9/ 9 000
Ignition system
Manufacture	SEM	SEM
Type of ignition system	CD	CD
Spark plug	NGK BPMR 7A	NGK BPMR 7A
Electrode gap, inch/mm	Champion RCJ 7Y	Champion RCJ 7Y
	0,2/0,5	0,2/0,5
Fuel and lubrication system
Manufacturer	Walbro	Walbro
Carburetor type	HDA175	HDA175
Fuel capacity, US pint/litre	1,27/0,7	1,27/0,7
Oil pump capacity at 8500 rpm, ml/min	5-15	5-15
Oil capacity, US pint/litre	0,69/0,38	0,69/0,38
Type of oil pump	Automatic	Automatic
Weight
Without bar and chain, Lbs/kg	12,1/5,5	12,1/5,5
Chain/bar	357XPG: 12,3/5,6	359G: 12,3/5,6
Standard bar length, inches/cm	15"/38	15"/38
Recommended bar lengths, inches/cm	13-24"/33-61	13-24"/33-61
Usable cutting length, inches/cm	12-23"/31-58	12-23"/31-58
Chain speed at max. power, m/sec	21,4	21,4
Pitch, inch/mm	0,325"/8,25	0,325"/8,25
Thickness of drive link, inch/mm	3/8"/9,52	3/8"/9,52
	0,058"/1,5	0,058"/1,5
Number of teeth on drive sprocket	7	7
Recommended original and replacement		Guide bar				Saw chain
bar and chain combinations		Length	Pitch		Max nose
Following is a list of recommended cutting equipment for the		inch	inch		radius
Husqvarna chain saw models 357XP and 359. The combinations of		13	0,325"		10T	Husqvarna H30 or
powerhead, bar and chain have been investigated in accordance with		15	0,325"		10T	Oregon 95VP
the kickback and vibration requirements of ANSI B 175.1 – 2000. The		16	0,325"		10T
guide bar nose radius is determined by either the maximum number		18	0,325"		10T
of teeth in the nose sprocket or the corresponding maximum nose		20	0,325"		10T
radius of a solid bar.
		13	0,325"		10T	Husqvarna H25 or
The following list is the chain saw manufacturers recommendations.		15	0,325"		10T	Oregon 21BP
There may be other combinations available, which will also achieve		16	0,325"		10T
kickback reduction.		18	0,325"		10T
As we are listing the maximum guide bar nose radius, you may use a		20	0,325"		12T
		15	0,325"		10T	Oregon 34LG
guide bar with smaller nose radius than in our list. For guide bars of
		16	0,325"		10T
the same length, all sprocket-nose guide bars of the same pitch and
		18	0,325"		10T
having the same number of of sprocket teeth may be considered to
		20	0,325"		12T
have equivalent kickback energy. A hard nose bar having the same
length and nose radius as a sprocket-nose bar may be considered to		15	3/8"		11T	Husqvarna H42 or
have equivalent or less kickback energy than the sprocket-nose bar.		16	3/8"		11T	Oregon 73LP/73LG/73V
Low kickback saw chain is a chain which has only met the kickback		18	3/8"		11T
		20	3/8"		11T
performance requirements of ANSI B 175.1 safety requirements for
		24	3/8"		11T
gasoline-powered chain saws when tested on the representative
sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We		Note: For the chains above you are free to choose between 0,050"
recommend that you as replacement use the listed chains or "Low		and 0,058" gauge drive link for the corresponding bar, see table
kickback saw chains" which are available at your dealer.		below.
		0,050"/1,3 mm		–	20BP	33LG	–	72LP	72LG	72V
		0,058"/1,5 mm		H25	21BP	34LG	H42	73LP	73LG	73V

34´+H%y¶5\¨

– English