Husqvarna 45 34«*3!35B¬, Technical Data, Recommended bar and chain combinations, Engine, system

TECHNICAL DATA

	45	49
Engine
Cylinder volume, cu.in/cm3	2,7/44	3,0/49
Cylinder bore, inch/mm	1,65/42	1,73/44
Stroke, inch/mm	1,26/32	1,26/32
Idle speed, rpm	2 500	2 500
Power, kW/ rpm	2,2/ 9 000	2,3/ 9 000
Ignition system
Manufacture	Phelon	Phelon
Type of ignition system	CD	CD
Spark plug	Champion	Champion
	RCJ 7Y	RCJ 7Y,
Electrode gap, inch/mm		NGK BPMR 7A
	0,020/0,5	0,020/0,5
Fuel and lubrication
system
Manufacturer	Zama	Zama
Carburetor type	C1Q-EL5	C1Q–EL5
Fuel capacity, US pint/litre	1,06/0,5	1,06/0,5
Oil pump capacity at
8 500 rpm, ml/min	8	8
Oil capacity, US pint/litre	0,53/0,25	0,53/0,25
Type of oil pump	Automatic	Automatic
Weight
Without bar and chain, Lbs/kg	10,3/4,7	10,4/4,7
Chain/bar
Standard bar length,
inches/cm	13"/33	13"/33
Recommended bar lengths,
inches/cm	13-18"/33-46	13-20"/33-51
Usable cutting length
inches/cm	12,6-17,5"/	12,6-19,5"/
Chain speed at max.	32-44,5	32-49,5
power, m/sec	17,4	17,4
Pitch, inch/mm	0,325"/8,25	0,325"/8,25
Thickness of drive link,
inch/mm	0,050"/1,3	0,050"/1,3
Number of teeth on drive	0,058"/1,5	0,058"/1,5
sprocket	7	7

34«*3!3¦5B¬

– English

Recommended bar and chain combinations

Following is a list of recommended cutting equipment for the Husqvarna Models 45 and 49. The combinations of powerhead, bar and chain have been investigated in accordance with the kickback requirements of ANSI B 175.1 – 1991. The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a solid bar.

The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback protection.

As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of of sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.

Low kickback saw chain is a chain which is has met the kickback performance requirements of ANSI B 175.1 safety requirements for gasoline-powered chain saws when tested on the representative sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We recommend that you as replacement use the listed chains or "Low kickback saw chains" which are available at your dealer.

Guide bar			Saw chain
Length	Pitch	Max nose
inch	inch	radius
13	0,325"	10T	Husqvarna H30/H25 or
15	0,325"	10T	Oregon 95VP/21VB
16	0,325"	10T
18	0,325"	10T
20	0,325"	12T	Husqvarna H25 or Oregon 21VB

NOTE: The second number in the Oregon part number indicate the thickness of the drive link. You are free to choose between 0,050" and 0,058" drive link for the corresponding bar.

OREGON 20 indicates 0,050"/1,3 mm

OREGON 21 indicates 0,058"/1,5 mm