Before Starting the Engine, Scraper BAR | Husqvarna 524STE specification

OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already ﬁlled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil ﬁ ll cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overﬁll.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank ﬁ ller neck. Do not over- ﬁll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open ﬂame.

CAUTION: Alcohol blended fuels (called gas- ohol or using ethanol or methanol) can attract moisture which leads to separation and for- mation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next sea- son. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE CONTROL	THROTTLE PRIMER ENGINE OIL
	FILL CAP /
	DIPSTICK

SAFETY

IGNITION

KEY

		GASOLINE
		FILLER CAP
		FUEL SHUT-
		OFF VALVE
	RECOIL	STARTER BUTTON
	STARTER	STARTER BUTTON
	STARTER
	HANDLE	POWER CORD PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

524STE specifications

The Husqvarna 524STE is a powerful and versatile snow thrower designed for homeowners who seek efficiency and performance in winter conditions. This piece of equipment is engineered to handle various types of snow, making it ideal for both light snowfalls and heavy snow accumulations. With its robust design and innovative features, the 524STE provides exceptional reliability and ease of use.

One of the standout features of the Husqvarna 524STE is its 24-inch clearing width. This allows the machine to clear large areas quickly, reducing the time spent on snow removal. The powerful engine, typically a 208cc 4-stroke, ensures that the snow thrower can handle dense snow even in harsh winter conditions. The 524STE also incorporates an easy-start mechanism, allowing for quick ignition even in cold weather, which is a significant advantage for early morning snow clearing.

The innovative two-stage snow thrower design is another key characteristic of the 524STE. This mechanism uses an auger to collect the snow before an impeller throws it away, which effectively reduces the likelihood of clogging and enhances performance. The adjustable chute allows operators to direct the snow precisely where they want it, providing better control and efficiency during operation.

Husqvarna has also equipped the 524STE with convenient features such as ergonomic controls and adjustable handle heights, which allow for comfortable operation for users of various sizes. The units are designed with durability in mind, featuring heavy-duty materials that can withstand harsh winter conditions. The snow thrower also comes with durable tires that enhance traction and maneuverability, enabling it to navigate various terrains effortlessly.

For added safety, the Husqvarna 524STE includes features such as a safety switch that ensures the machine only operates when the operator is in control. Easy maintenance options also allow for extended use, as owners can quickly service the machine as needed.

With its impressive range of features, advanced technologies, and user-friendly design, the Husqvarna 524STE is an excellent investment for anyone looking to tackle winter weather with confidence and efficiency. Whether managing the driveway or clearing pathways, this snow thrower proves to be a reliable partner in any snow-clearing task.

Husqvarna 524STE owner manual Before Starting the Engine, Scraper BAR, To Start Engine

Models: 524STE