Manuals / Husqvarna / Lawn and Garden / Tiller

Husqvarna DRT900E TO ADJUST THROTTLE CONTROL CABLE See Fig, To Adjust Carburetor, Engine

Models: DRT900E

1 28

Download 28 pages 42.54 Kb

Page 18

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, proceed as follows:

•With engine not running, move remote throttle control lever to “FAST” position.

•If throttle lever on engine touches high speed stop, no further adjustment is necessary. If throttle lever does not touch high speed stop, continue with adjustment procedure.

•Loosen cable clamp screw.

•Move throttle lever up until it touches high speed stop, and hold in this position.

•Tighten cable clamp screw securely.

CLAMP SCREW

CASING

AND WIRE

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, engine performance can be affected by differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, contact your nearest authorized service center/department

IMPORTANT:NEVERTAMPERWITHTHEENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

engine_art_78

THROTTLE CONTROL

Fig. 30

18

Image 18

Husqvarna DRT900E TO ADJUST THROTTLE CONTROL CABLE See Fig, To Adjust Carburetor, Service And Adjustments, Engine

Contents

DRT900E 532MAINTENANCE AND STORAGE SAFETY RULESSafe Operation Practices for Walk-Behind Powered Rotary Tillers TRAININGCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS 12-14CONTENTS OF HARDWARE PACK ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY OPERATOR’S POSITION See FigINSTALL HANDLE See Figs. 3, 4, and UNPACKING CARTON See FigASSEMBLY REMOVE TILLER FROM CRATE ATTACH CLUTCH CABLE See FigCONNECT SHIFT ROD See Fig CHECK TIRE PRESSUREMEETS ANSI SAFETY REQUIREMENTS OPERATIONKNOW YOUR TILLER TINE OPERATION - WITH WHEEL DRIVE HOW TO USE YOUR TILLERSTOPPING See Fig FORWARD - WHEELS ONLY/TINES STOPPEDOUTER SIDE SHIELDS See Fig TURNINGCULTIVATING TO TRANSPORTPower Cord ADD GASOLINETO START ENGINE See Fig OPERATIONOPERATION ADJUST WHEELS FOR CULTIVATING See Figs. 17 andTILLING HINTS See Fig CULTIVATINGLUBRICATION CHART MAINTENANCEMAINTENANCE SCHEDULE GENERAL RECOMMENDATIONSDo not touch hot muffler or cylinder fins as contact may cause burns ENGINEAIR FILTER See Fig TO CHANGE ENGINE OIL See Figs. 19 andMUFFLER CLEANINGCOOLING SYSTEM See Fig SPARK PLUGTILLER SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TIRE CAREGROUND DRIVE BELT ADJUSTMENT S e e Fig TO REPLACE GROUND DRIVE BELT See Figs. 25 andSERVICE AND ADJUSTMENTS TINE REPLACEMENT See Figs. 27, 28 and SERVICE AND ADJUSTMENTStine20 SERVICE AND ADJUSTMENTS TO ADJUST THROTTLE CONTROL CABLE See FigTO ADJUST CARBURETOR ENGINEFUEL SYSTEM STORAGEOTHER ENGINE OILTROUBLESHOOTING POINTS TILLER - - MODEL NUMBER DRT900E 96093001401, PRODUCT NUMBER REPAIR PARTSHANDLE ASSEMBLY PARTTILLER - - MODEL NUMBER DRT900E 96093001401, PRODUCT NUMBER MAINFRAME, LEFT SIDEREPAIR PARTS PARTKEY PART NO. NO. DESCRIPTION MAINFRAME, RIGHT SIDE REPAIR PARTSTRANSMISSION REPAIR PARTSTILLER - - MODEL NUMBER DRT900E 96093001401, PRODUCT NUMBER 960 KEY PART NO. NO. DESCRIPTIONTILLER - - MODEL NUMBER DRT900E 96093001401, PRODUCT NUMBER TINE SHIELDREPAIR PARTS PARTTILLER - - MODEL NUMBER DRT900E 96093001401, PRODUCT NUMBER 960 TINE ASSEMBLYREPAIR PARTS KEY PART NO. NO. DESCRIPTIONTILLER - - MODEL NUMBER DRT900E 96093001401, PRODUCT NUMBER DECALSREPAIR PARTS KEY PART NO. NO. DESCRIPTION10.28.10 CL