Mowing Tips, Purge Transmission | Husqvarna GTH2754 manual

OPERATION

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

NOTE:In extreme cold conditions, if engine will not start, you may need to disengage the motion drive belt as follows:

•Be sure parking brake is engaged.

•Remove retainer spring from the drive belt tension handle to relieve belt tension.

•Start engine and allow it to warm up for three (3) min- utes.

•Shut-off engine and engage parking brake.

•Engage drive belt tension handle and replace the retainer spring.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

•Move motion control lever to full forward position and hold for ﬁve (5) seconds. Move lever to full reverse position and hold for ﬁve (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Slowly move motion control lever forward, after the tractor moves approximately ﬁve (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately ﬁve (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your tractor is now purged and now ready for normal operation.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

•Whenmowinglargeareas,startbyturningtotherightsothat clippingswilldischargeawayfromshrubs,fences,driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until ﬁnished (See Fig. 12).

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run- ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the ﬁrst time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake

00272

FIG. 12

• If grass is extremely tall, it should be mowed twice to reduce load and possible ﬁre hazard from dried clip- pings. Make ﬁrst cut relatively high; the second to the desired height.

• Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

• Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of

the attachment being used.

GTH2754 specifications

The Husqvarna GTH2754 is a powerful and versatile garden tractor designed for homeowners looking to maintain their lawns with efficiency and ease. This exceptional machine combines robust construction with innovative technologies, making it a favorite among gardening enthusiasts.

One of the standout features of the GTH2754 is its powerful 27-horsepower Briggs & Stratton engine. This reliable engine ensures that the tractor delivers consistent performance, enabling users to tackle various tasks with confidence. Whether mowing large lawns or navigating tight spaces, the ample power makes it suitable for a range of applications, including mulching and bagging.

The GTH2754 is equipped with a 54-inch cutting deck, allowing for wider cutting swath and a quicker mowing experience. The cutting deck features three large blades designed to give an even and clean cut, ensuring an aesthetically pleasing lawn. With adjustable cutting heights ranging from 1.5 inches to 4 inches, users can customize the lawn's appearance according to their preferences and seasonal requirements.

Comfort is a crucial aspect of the GTH2754, featuring an ergonomic, high-back seat designed for operator comfort during extended use. The seat is adjustable, accommodating different user heights for optimal driving posture. Additionally, the tractor comes equipped with a user-friendly control panel, where operators can easily access key functions like speed control and cutting height adjustment.

The GTH2754 showcases Husqvarna's commitment to innovative technology. The automatic transmission system provides smooth and effortless operation, allowing users to focus on their mowing tasks without needing to grapple with gear shifting. This feature ensures that the tractor can maintain a steady pace, adapting to various terrain conditions effortlessly.

Moreover, the tractor is designed for easy maintenance, with features like an accessible oil filter and removable engine cover. This makes routine checks and servicing straightforward, prolonging the lifespan of the machine.

Overall, the Husqvarna GTH2754 is a robust and user-friendly garden tractor that caters to the needs of modern homeowners. Its powerful engine, large cutting deck, and thoughtful design make yard maintenance not just manageable but also enjoyable. With its combination of performance and comfort, the GTH2754 is indeed a valuable investment for any gardening enthusiast.

Husqvarna GTH2754 owner manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Models: GTH2754