OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or
performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles 
00155or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 6)
Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without fi rst setting the parking brake will shut off the engine.
•Depress brake pedal into full “BRAKE” position and hold.
•Place parking brake lever in “ENGAGED” position and release pressure from brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure.
CHOKE | ATTACHMENT CLUTCH SWITCH | ||
CONTROL PULL OUT TO “ENGAGE” | |||
THROTTLE |
|
| |
CONTROL | IGNITION | PUSH IN TO | |
HEIGHT | KEY | “DISENGAGE” | |
ADJUSTMENT |
|
| |
KNOB |
| REVERSE | |
|
| ||
“BRAKE” |
| PEDAL | |
|
| ||
POSITION |
|
| |
|
| FORWARD | |
02528 |
| PEDAL | |
|
| CRUISE CON- | |
|
| TROL LEVER | |
|
| PARKING BRAKE | |
BRAKE PEDAL | “DISENGAGED” | “ENGAGED” | |
POSITION | |||
“DRIVE” POSITION | |||
POSITION |
| ||
|
| ||
FIG. 6
NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.
CAUTION: Always stop tractor com- pletely,as described above,before leav- ing the operator's position; to empty grass catcher, etc.
TO USE THROTTLE CONTROL (See Fig. 6)
Always operate engine at full throttle.
•Operating engine at less than full throttle reduces the battery charging rate.
•Full throttle offers the best bagging and mower perfor- mance.
TO USE CHOKE CONTROL (See Fig. 6)
Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.
•To engage choke control, pull knob out. Slowly push knob in to disengage.
TO MOVE FORWARD AND BACKWARD (See Fig. 6)
The direction and speed of movement is controlled by the forward and reverse drive pedals.
•Start tractor and release parking brake.
•Slowly depress forward or reverse drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.
STOPPING (See Fig. 6)
MOWER BLADES -
•To stop mower blades,move attachment clutch switch to “DISENGAGED” position.
GROUND DRIVE -
•To stop ground drive, depress brake pedal into full “BRAKE” position.
IMPORTANT: FORWARD AND REVERSE DRIVE PEDALS RETURN TO NEUTRAL POSITION WHEN NOT DEPRESSED.
ENGINE -
•Move throttle control between half and full speed (fast) position.
NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping may cause engine to “backfire”.
•Turn ignition key to “STOP” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.
•Never use choke to stop engine.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).
TO USE CRUISE CONTROL
The cruise control feature can be used for forward travel only.
SYSTEM CHARACTERISTICS
The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrain or while trimming or turning.
•With forward drive pedal depressed to desired speed, move cruise control lever forward to “SET” position and hold while lifting your foot off the pedal, then release the cruise control lever.
•To disengage the cruise control, pull the lever backward to “OFF” position, or fully depress the brake pedal.
TO ADJUST MOWER CUTTING HEIGHT (See Fig. 6)
The cutting height is controlled by turning the height ad- justment knob in desired direction.
• | Turn knob clockwise ( ) to raise cutting height. |
• | Turn knob counterclockwise ( ) to lower cutting |
11 | height. |
|
