Manuals / Brands / Lawn and Garden / Lawn Mower / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna YTH 2448 TO REMOVE MOWER (See Fig. 18), TO INSTALL MOWER

1 48

Download 48 pages, 2.26 Mb

20

FIG. 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST -

MENTS:

• Depress clutch/brake pedal fully and set parking brake.

• Place motion control lever in neutral (N) position.

• Place attachment clutch in “DISENGAGED” position.

• Turn ignition key to “STOP” and remove key.

• Make sure the blades and all moving parts have completely stopped.

• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact

with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 18)

• Place attachment clutch in “DIS EN GAGED” position.

• If equipped, turn height adjustment knob to low est

set ting.

• Lower mower to its lowest position.

• Remove retainer spring holding anti-swaybar to chas sis

bracket and dis en gage anti-swaybar from bracket.

• Remove four retainer springs from front plate assembly

and remove plate.

• Remove retainer springs from sus pen sion arms at deck

and dis en gage arms from deck.

• Raise attachment lift to its highest position.

• Slide mower forward and remove belt from electric

clutch pulley.

• Slide mower out from under right side of tractor.

TO INSTALL MOWER

Be sure tractor is on level surface and mower suspension

arms are raised with attachment lift control. Engage park-

ing brake.

• Swing anti-sway bar to left side of mower deck.

• Slide mower under tractor with deﬂ ector shield to right

side of tractor.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL

MOWER PULLEY GROOVES.

• If equipped, turn height ad just ment knob coun ter -

clock wise until it stops.

• Lower mower linkage with attachment lift control.

• Install belt into electric clutch pulley groove.

• Place the suspension arms on outward pointing deck

pins. Retain with double loop re tain er spring with loops

up as shown.

• Install front plate assembly to tractor suspension

brack ets and retain with single loop retainer springs

as shown.

02566

SUSPENSION

ARMS

RETAINER

SPRING

ANTI-SWAY

BAR

SUSPENSION ARMS

DOUBLE LOOP

RETAINER SPRINGS

(Out ward pointing

deck pins)

CHASSIS

BRACK ET

SINGLE LOOP

REATINER

SPRING

FRONT

MOWER

BRACKET

FLANGED PINS

ELECTRIC

CLUTCH

PULLEY FRONT PLATE

AS SEM BLY

USE PLIERS FOR

RETAINER SPRINGS

LOOP UP

DOUBLE LOOP

RETAINER SPRING

Contents

Main I. GENERAL OPERATION SAFETY RULES Safe Operation Practices for Ride-On Mowers WARNING II. SLOPE OPERATION SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Never IV. TOWING V. SERVICE TABLE OF CONTENTS CUSTOMER RESPONSIBILITIES UNASSEMBLED PARTS Steering Wheel Seat Mower Gauge Wheels TOOLS REQUIRED FOR ASSEMBLY TO REMOVE TRACTOR FROM CARTON UNPACK CARTON CHECK BATTERY (See Fig. 2) BEFORE REMOVING TRAC TOR FROM SKID ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 5) TO ATTACH NOSE ROLLER (See Fig. 4) INSTALL SEAT (See Fig. 3) TO ROLL TRACTOR OFF SKID (See Op- er a tion section for location and function of con trols) TO DRIVE TRAC TOR OFF SKID (See Op- er a tion section for location and function of con trols) INSTALL MOWER AND DRIVE BELT (See Figs. 6 and 7) CHECK TIRE PRESSURE CHECK MOWER LEV EL NESS CHECK FOR PROPER POSITION OF ALL BELTS CHECK BRAKE SYSTEM CHECKLIST Page KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR TO ADJUST GAUGE WHEELS (See Fig. 9) HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 8) TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8) TO MOVE FORWARD AND BACKWARD (See Fig. 8) TO USE THROTTLE CONTROL (See Fig. 8) TO OPERATE MOWER (See Fig. 10) TO OPERATE ON HILLS REVERSE OPERATION SYSTEM (ROS) TO START ENGINE (See Fig. 8) TOWING CARTS AND OTHER AT TACH - MENTS BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL TO TRANSPORT (See Figs. 7 and 11) MOWING TIPS PURGE TRANSMISSION T R A C T 0 R MAINTENANCE SCHEDULE SERVICE DATES GENERAL RECOMMENDATIONS BEFORE EACH USE BLADE REMOVAL (See Fig. 13) TO SHARPEN BLADE (See Fig. 14) TRANSAXLE COOLING TRANSAXLE PUMP FLUID V-BELTS LUBRICATION BATTERY CLEANING CLEAN AIR INTAKE/COOLING AREAS AIR FILTER TO REMOVE MOWER (See Fig. 18) TO INSTALL MOWER TO LEVEL MOWER HOUSING TO REPLACE MOWER DRIVE BELT TO REPLACE MOWER BLADE (SEC OND ARY) DRIVE BELT (See Fig. 24) TO CHECK AND ADJUST BRAKE (See Fig. 25) TO REPLACE MOTION DRIVE BELT (See Fig. 26) TRANSAXLE MOTION CONTROL LE VER NEUTRAL ADJUSTMENT (See Fig. 27) TRANSMISSION REMOVAL/RE PLACE MENT TO AD JUST STEER ING WHEEL ALIGN MENT FRONT WHEEL TOE-IN/CAMBER TO START ENGINE WITH A WEAK BATTERY(See Fig. 29) REPLACING BATTERY (See Fig. 30) TO REPLACE HEADLIGHT BULB TO REPLACE FUSE TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31) TO AD JUST THROTTLE CON TROL CABLE STORAGE BATTERY FUEL SYSTEM ENGINE OIL CYLINDER(S) TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION SCHEMATIC Page ELECTRICAL CHASSIS AND ENCLOSURES 74 chassis_elite husqy_4 Page Page DRIVE STEERING ASSEMBLY steering_pl.lt_54 Page SEAT ASSEMBLY DECALS WHEELS & TIRES ENGINE OPTIONAL EQUIPMENT Spark Arrester ENGINE Page MOWER LIFT TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07 MOWER DECK FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARRANTY STATEMENT SECTION 1: LIMITED WARRANTY SECTION 2: HUSQVARNAS OBLIGATIONS UNDER THE WARRANTY SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY SECTION 4: EXCEPTIONS AND LIMITATIONS