Husqvarna YTH 2448 MOWER DECK

45

REPAIR PARTS

TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07

MOWER DECK

KEY PART

NO. NO. DESCRIPTION KEY PART

NO. NO. DESCRIPTION

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

1 532 18 03-58 Deck Weldment Mower 48

3 532 13 80-17 Bracket Asm., Sway Bar

5 532 12 46-70 Retainer Spring

6 532 17 80-24 Bar Sway Deck

8 532 17 43-65 Bolt, 7/16 Asm. Blade

11 532 18 00-54 Blade

13 532 17 43-60 Shaft Asm. Mandrel Sealed

14 532 17 43-58 Housing Mandrel 48"

15 532 11 04-85 Bearing, Ball, Mandrel

16 532 17 44-93 Stripper, Mower

17 872 11 06-10 Bolt Rdhd Sq Neck 3/8-16 x 1.25

18 872 14 05-05 Bolt, Carriage 5/16-18 x 5/8

19 532 13 28-27 Bolt, Hex Head, Shoulder 5/16-18

20 532 17 43-78 Bafﬂ e, Vortex Mower

21 873 68 05-00 Nut, Crownlock 5/16-18 unc

24 532 10 53-04 Cap, Sleeve

25 532 17 81-02 Spring, Torsion

26 532 11 04-52 Nut, Push

27 532 18 17-07 Shield, Deﬂ ector Mower

28 819 11 10-16 Washer 11/32 x 5/8 x 16 Ga.

29 532 13 14-91 Rod, Hinge

30 532 17 39-84 Screw, Thdroll, Washer Head

31 532 18 76-90 Washer, Spacer Mower Vented

32 532 17 34-36 Pulley, Mandrel

33 532 17 83-42 Nut, Flg. Top Lock Cntr. 9/16

37 532 17 79-68 Pulley, Idler, Flat

39 532 17 43-75 Pulley, Idler, Driven

42 532 12 20-52 Spacer, Retainer

43 532 17 43-73 Arm, Idler Secondary

45 532 18 08-06 Cover, Mandrel Deck

46 532 13 77-29 Screw, Thdroll. 1/4-20 x 5/8

47 532 18 08-08 V-Belt, Mower, Secondary

48 532 17 43-68 V-Belt, Mower, Primary

49 873 90 06-00 Nut, Lock 3/8-16 unc

50 872 11 06-12 Bolt, Carriage 3/8-16 x 1-1/2 Gr. 5

52 532 17 58-20 Pulley Idler Flat 46 Pri. Drive

54 874 78 06-16 Bolt Fin Hex 3/8-16 x 1

55 872 14 06-08 Bolt Rdhd Sqnk 3/8-16 x 1

56 532 15 59-86 Bar Pnt Adjusting Wheel Gauge

57 532 15 69-41 Pin Head Rivet

72 819 13 13-12 Washer 13/32 x 13/16 x 12

91 532 18 05-35 Bracket, Asm Noseroller, RH 48

92 873 80 06-00 Nut Lock Hex w/Ins 3/8-16

94 532 17 60-66 Roller, Nose 48"

95 532 18 05-34 Bracket, Asm Noseroller LH 48

97 532 17 85-15 Washer Hardened

98 532 17 94-79 Spring Primary Drive

99 532 18 99-93 Pulley Idler "V"

100 872 11 06-16 Bolt RDHD Sqnk 3/8-16 unc x 2

110 532 17 50-16 Arm Spring Secondary

111 532 17 46-10 Arm Spring Fixed Tension

116 532 18 42-19 Bolt, Shoulder

117 532 17 48-73 Gauge Wheel

118 873 93 06-00 Nut, Centerlock 3/8-16 unc

119 819 12 14-14 Washer 3/8 x 7/8 x 14 Ga.

121 532 17 43-71 Spring Secondary Drive

126 532 17 43-72 Arm, Idler, Primary Deck

130 817 00 06-16 Screw 3/8-16 x 1.0

131 819 13 16-06 Washer 13/32 x 1 x 6 Ga.

132 817 00 06-12 Screw 3/8-16 x 3/4

133 872 11 05-06 Bolt Rdhd Sqnk 5/16-18 unc x 3/4

182 532 17 91-27 Rod Roller Nose

183 532 16 35-52 Retainer Spring

184 532 17 39-79 Keeper Belt Idler

- - 532 17 43-57 Mandrel Assembly (Includes Hous-

ing, Shaft and Shaft Hardware

Only-Pulley Not Included)

- - 532 18 99-06 Replacement Mower, Complete

(Std Deck-Order Separately Nose

Roller Components Key Nos. 91,

94, 95, 132, 182-183)

Contents

Main I. GENERAL OPERATION SAFETY RULES Safe Operation Practices for Ride-On Mowers WARNING II. SLOPE OPERATION SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Never IV. TOWING V. SERVICE TABLE OF CONTENTS CUSTOMER RESPONSIBILITIES UNASSEMBLED PARTS Steering Wheel Seat Mower Gauge Wheels TOOLS REQUIRED FOR ASSEMBLY TO REMOVE TRACTOR FROM CARTON UNPACK CARTON CHECK BATTERY (See Fig. 2) BEFORE REMOVING TRAC TOR FROM SKID ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 5) TO ATTACH NOSE ROLLER (See Fig. 4) INSTALL SEAT (See Fig. 3) TO ROLL TRACTOR OFF SKID (See Op- er a tion section for location and function of con trols) TO DRIVE TRAC TOR OFF SKID (See Op- er a tion section for location and function of con trols) INSTALL MOWER AND DRIVE BELT (See Figs. 6 and 7) CHECK TIRE PRESSURE CHECK MOWER LEV EL NESS CHECK FOR PROPER POSITION OF ALL BELTS CHECK BRAKE SYSTEM CHECKLIST Page KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR TO ADJUST GAUGE WHEELS (See Fig. 9) HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 8) TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8) TO MOVE FORWARD AND BACKWARD (See Fig. 8) TO USE THROTTLE CONTROL (See Fig. 8) TO OPERATE MOWER (See Fig. 10) TO OPERATE ON HILLS REVERSE OPERATION SYSTEM (ROS) TO START ENGINE (See Fig. 8) TOWING CARTS AND OTHER AT TACH - MENTS BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL TO TRANSPORT (See Figs. 7 and 11) MOWING TIPS PURGE TRANSMISSION T R A C T 0 R MAINTENANCE SCHEDULE SERVICE DATES GENERAL RECOMMENDATIONS BEFORE EACH USE BLADE REMOVAL (See Fig. 13) TO SHARPEN BLADE (See Fig. 14) TRANSAXLE COOLING TRANSAXLE PUMP FLUID V-BELTS LUBRICATION BATTERY CLEANING CLEAN AIR INTAKE/COOLING AREAS AIR FILTER TO REMOVE MOWER (See Fig. 18) TO INSTALL MOWER TO LEVEL MOWER HOUSING TO REPLACE MOWER DRIVE BELT TO REPLACE MOWER BLADE (SEC OND ARY) DRIVE BELT (See Fig. 24) TO CHECK AND ADJUST BRAKE (See Fig. 25) TO REPLACE MOTION DRIVE BELT (See Fig. 26) TRANSAXLE MOTION CONTROL LE VER NEUTRAL ADJUSTMENT (See Fig. 27) TRANSMISSION REMOVAL/RE PLACE MENT TO AD JUST STEER ING WHEEL ALIGN MENT FRONT WHEEL TOE-IN/CAMBER TO START ENGINE WITH A WEAK BATTERY(See Fig. 29) REPLACING BATTERY (See Fig. 30) TO REPLACE HEADLIGHT BULB TO REPLACE FUSE TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31) TO AD JUST THROTTLE CON TROL CABLE STORAGE BATTERY FUEL SYSTEM ENGINE OIL CYLINDER(S) TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION SCHEMATIC Page ELECTRICAL CHASSIS AND ENCLOSURES 74 chassis_elite husqy_4 Page Page DRIVE STEERING ASSEMBLY steering_pl.lt_54 Page SEAT ASSEMBLY DECALS WHEELS & TIRES ENGINE OPTIONAL EQUIPMENT Spark Arrester ENGINE Page MOWER LIFT TRACTOR - MODEL NO. YTH2448 (279081), PRODUCT NO. 960 13 00-07 MOWER DECK FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARRANTY STATEMENT SECTION 1: LIMITED WARRANTY SECTION 2: HUSQVARNAS OBLIGATIONS UNDER THE WARRANTY SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY SECTION 4: EXCEPTIONS AND LIMITATIONS