![WIRING COLOR CODE](/images/new-backgrounds/70796/7079625x1.webp)
Rev. 0904
Electrical
WIRING COLOR CODE
STANDARD CASE WIRE COLOR CODE
CODIGO DE COLORES DE LOS ALAMBRES PARA LAS VITRINAS ESTANDAR
CODE COULEUR POUR FILS DE BOITIER NORMALISE
C o l o r D e s c r i p t i o n | D e s c r i p c i o n | D e s c r i p c i o n | |||
|
|
| GROUND | TIERRA MASA | MASSE |
|
|
| ANTI - SWEAT | ANTICONDENSCION | ANTI - SUINTEMENT |
|
|
| |||
|
| ||||
|
|
| LIGHTS | LUCES | ECLAIRAGE |
|
|
| |||
|
| ||||
|
|
| RECEPTACLES | ENCHUFER | RECEPTACLE |
|
|
| |||
|
| ||||
|
|
| T- STAT/SOLENOID 230 V | THERMOSTATO / SOLENOID (230 VAC) | SOUPAPE A SOLENOID (230 V) |
|
|
| |||
|
| ||||
|
|
| T- STAT/SOLENOID 115 V | THERMOSTATO / SOLENOID (115 VAC) | SOUPAPE A SOLENOID (115 V) |
|
|
| FAN MOTORS | VENTILADORES | VENTILATEUR |
|
|
| |||
|
|
|
| 430 - 01 - 0338 r9908 |
CASE MUST BE GROUNDED
NOTE: Refer to label illustrated above that is affixed to case to determine the actual configuration as checked in the “TYPE INSTALLED” boxes.
ELECTRICAL CIRCUIT IDENTIFICATION
Standard lighting for all models will be full length fluores- cent lamps located within the case at the top.
The switch controlling the lights, the plug provided for digital scale, and the thermometer are located at the rear of the case mullion.
less than specified. Field wiring from the refrigeration control panel to the merchandisers is required for re- frigeration thermostats. Most component amperes are listed in the “Case Specs” section, but always check the serial plate.
BALLAST LOCATION
Ballasts are located within the access panel that runs the length of the rear of the case. Refer to diagram on page 6.
WIRING & SERIAL PLATE AMPERAGE
Field Wiring must be sized for component amperes stamped on the serial plate. Actual ampere draw may be less than specified. Field wiring from the refrigeration con trol panel to the merchandisers is required for refrigera- tion thermostats. Most component amperes are listed in the "Case Specs" section, but always check the serial plate.
ASHRAE COLOR CODE
NOTE: All other manufacturers have no standard sensor codes.
ELECTRICAL SERVICE RECEPTACLES (WHEN APPLICABLE)
The receptacle that is provided on the exterior back of these models is intended for computerized scales with a fifteen amp maximum load, not for large motors or other high wattage appliances. It should be wired to a dedicated circuit.
BEFORE SERVICING
ALWAYS DISCONNECT ELECTRICAL POWER AT THE MAIN DISCONNECT WHEN SERVICING OR REPLACING ANY ELECTRICAL COMPONENT.
This includes (but not limited to) Fans, Heat-
ers, Thermostats, and Lights.
FIELD WIRING & SERIAL PLATE AMPERAGE
Field Wiring must be sized for component amperes printed on the serial plate.Actual ampere draw may be
Case Control Systems | SENSOR COLOR |
| |
|
|
|
|
Manufacturer ® > |
| EIL | CP |
|
|
|
|
Location |
|
|
|
|
|
|
|
Coil Inlet | Color | Blue | Blue |
|
|
|
|
| Part# | ||
|
|
|
|
Coil Outlet | Color | Red | Red |
|
|
|
|
| Part# | ||
|
|
|
|
Discharge Air | Color | Green | Green |
|
|
|
|
| Part# | ||
|
|
|
|
Return Air | Color | Purple | Green |
|
|
|
|
| Part# | ||
|
|
|
|
Defrost Term. | Color | White | Orange |
|
|
|
|
| Part# | ||
|
|
|
|
Liquid Line | Color | White | Blue |
|
|
|
|
| Part# | ||
|
|
|
|
13