Manuals / IBM Partner Pavilion / Computer Equipment / Personal Computer

IBM Partner Pavilion 8123, 8138, 8137, 8131 Connecting drives, Connecting the first optical drive

Models: 8123 8122 8124 8131 8137 8138

1 64

Download 64 pages 57.64 Kb

Page 35

Connecting drives

9.Install the front bezel by aligning the plastic tabs on the bottom of the bezel with the corresponding holes in chassis and press it onto the chassis until it snaps into position.

10.Continue at “Connecting drives.”

Connecting drives

The steps to connect a drive are different depending on the type of drive. Use one of the following procedures for your drive connection.

Connecting the first optical drive

1.The drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board.

2.Locate the three-connector signal cable that comes with your computer or with the new drive.

3.Locate the PATA IDE connector on the system board. See “Identifying parts on the system board” on page 12.

4.Connect one end of the signal cable to the drive and the other to the PATA IDE connector on the system board. To reduce electronic noise, use the connectors at the end of the cable only.

5.Locate the extra four-wire power connector labelled P4 and connect it to the drive.

Chapter 1. Installing options 19

Image 35

IBM Partner Pavilion 8123, 8138, 8137, 8131, 8124, 8122 manual Connecting drives, Connecting the first optical drive

Contents

User Guide Types 8131, 8137 Types 8122, 8123 Page User Guide Types 8131, 8137 Types 8122, 8123 Third Edition May Contents iv User Guide Conditions that require immediate action Important safety informationService General safety guidelinesDanger Hazardous moving parts. Keep fingers and other body parts away Power cords and power adaptersExtension cords and related devices viii User Guide Plugs and outletsBatteries Heat and product ventilation CD and DVD drive safetyDanger Additional safety informationLithium battery notice Danger of explosion if battery is incorrectly replacedDanger Modem safety informationLaser compliance statement xii User Guide Power supply statementxiii OverviewInformation resources xiv User Guide System information Chapter 1. Installing optionsFeatures Note Use only the parts provided by LenovoInternal drives System management featuresInput/output features MemoryOperating systems, preinstalled varies by model type PowerSecurity features Preinstalled softwareThis section lists the physical specifications for your computer SpecificationsTools required Available optionsHandling static-sensitive devices Installing external optionsNote Not all computer models will have the following connectors Locating the connectors on the front of your computer8 User Guide Locating the connectors on the rear of your computerDescription Obtaining device driversConnector Removing the cover 7 Hard disk drive 8 Internal speaker 9 Diskette drive Locating components1 Optical drive 2 Memory modules 3 Power supply 4 PCI adapter connector 5 PCI adapter card 6 System board12 User Guide Identifying parts on the system boardWhat to do next Installing memory14 User Guide Installing adaptersWhat to do next Installing internal drivesDrive specifications The following illustration shows the locations of the drive bays Installing a drive in bay 1 or bay v If it is the first CD drive or DVD drive, set it as a master device Connecting the first optical drive Connecting drives20 User Guide Connecting a serial ATA hard disk driveWhat to do next 1 Padlock loop 2 Integrated cable lock Installing security featuresIdentifying security locks 22 User Guide PadlockWhat to do next Password protectionChanging the battery Integrated cable lock24 User Guide Erasing a lost or forgotten password clearing CMOSReplacing the cover and connecting the cables 26 User Guide Using passwords Chapter 2. Using the Setup Utility programStarting the Setup Utility program Viewing and changing settings3. Select Security Profile by Device Administrator PasswordSetting, changing, and deleting a password Using Security Profile by DeviceChanging the startup sequence Exiting from the Setup Utility programSelecting a startup device Selecting a temporary startup device30 User Guide System programs Updating flashing BIOS from a diskette or CD-ROMUpdating flashing BIOS from your operating system Appendix A. Updating system programsb. Click Continue c. Click Downloads and drivers Recovering from a POST/BIOS update failureCleaning a mouse with a ball Appendix B. Cleaning the mouseCleaning an optical mouse 8. Replace the ball and the retainer ring ATH ENTER Appendix C. Manual modem commandsBasic AT commands 36 User Guide Appendix C. Manual modem commands Extended AT commands38 User Guide MNP/V.42/V.42bis/V.44 commandsFax Class 2 commands Fax Class 1 commands40 User Guide Voice commandsBakom 93.0291.Z.N Attention Switzerland UserTelekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art 42 User Guide Attention Lenovo Director of Licensing Appendix D. NoticesLenovo United States, Inc 500 Park Offices Drive, Hwy Research Triangle Park, NC U.S.A44 User Guide Television output noticeTrademarks Index A Page Page 1P P/N 39J7710 Part Number 39J7710 Printed in USA