65
5INITIAL SETTING AFTER INSTALLATION
This item allows you to make a selection between two options on graphic
indication on the navigation monitor screen:
•NOR: Normal indication
•REVS: Reverse indication
This item allows you to make a selection between two options on Time indi-
cation on the navigation monitor screen:
•LOCAL: Local standard time
•GMT: Greenwich Mean Time (UTC)
The following describes how to set the offset time between UTC (Universal
Time Coordinated) and the standard time of a time zone.
The offset time of the system defaults to “+9”.
qSelect “SETTING” on the Setting Menu screen using the [UP] or [DOWN] key
and press the [SET] key.
The SETTING screen will appear.
wSelect “OFFSET TIME” using the [UP] or [DOWN] key and press the [SET] key.
eMove to the time difference setting field using the [LEFT] or [RIGHT] key.
The selected item is highlighted in yellow.
rEnter the desired value into the time difference setting field using the [UP] or
[DOWN] key and press the [SET] key.
The setting is saved.
tWhen you finish setting the offset time, press the [MENU] key.
You will return to the SETMODE screen.
This item allows you to make a selection between two ship speed signal sensing
options.
•POS: Signals received by the GPS receiver are used to read the ship speed.
•SENS: Signals detected by the sensor are used to read the ship speed.
The following describes how to correct the ship speed for difference between
the actual speed and the speed sensor reading.
qSelect “SETTING” on the SETMODE screen using the [UP] or [DOWN] key and
press the [SET] key.
The SETTING screen will appear.
wSelect “SPEED ADJ” using the [UP] or [DOWN] key and press the [SET] key.
eEnter the pulse rate of the speed sensor into the pulse rate setting field using
[UP] or [DOWN] key and press the [SET] key.
*When using an optional sensor, EX-1622 (transom type speed/temperature sen-
sor), set the pulse rate to “24000 P/NM”.
When using an optional transducer, EX-1010 (through-the-hull type transducer
with speed/water temperature sensor), set the pulse rate to “22000 P/NM”.
*If the above setting causes an error to occur, adjust the pulse rate while refer-
ring to the speed reading displayed on the screen.
rWhen you finish correcting the ship speed, press the [MENU] key.
You will return to the SET MODE screen.
|COMPASSIND
|TIME REF
|OFFSET TIME
|SPEED DATA
|SPEED ADJ
DATUM
BEARING
COMPASS IND
TIME REF
OFFSET TIME
123
TRUE
NOR
LOCAL
+ 9 : 00
MAG
REVS
GMT
BEARING
COMPASS IND
TIME REF
OFFSET TIME
SPEED DATA
SPEEDADJ
TRUE
NOR
LOCAL
+ 9 : 00
POS
24000P/
MAG
REVS
GMT
SENS
NM
SETTING
AUTO GAIN
DRAFT ADJ
TEMP ADJ
DATUM
BEARING
COMPASS IND
TIME REF
OFFSET TIME
SPEED DATA
SPEED ADJ
NMEA OUT
BOD OUT
ON
7.5 FT
+ 2.4 °F
TEMP
123
TRUE
NOR
LOCAL
+09 : 00
POS
24000 P/
SPEED
V1 . 5
WP
OFF
. °F
MAG
REVS
GMT
SENS
NM
0 . 0KT
V2 . 2
SHIP
CLR
CANC SEL
ADJ SET
SET
TIME REF
OFFSET TIME
SPEED DATA
SPEED ADJ
NMEA OUT
LOCAL
+ 9 : 00
POS
24000 P/
SPEED
V1 . 5
GMT
SENS
NM
0 . 0KT
V2 . 2
SETTING
AUTO GAIN
DRAFT ADJ
TEMP ADJ
DATUM
BEARING
COMPASS IND
TIME REF
OFFSET TIME
SPEED DATA
SPEED ADJ
NMEA OUT
BOD OUT
ON
7.5 FT
+ 2.4 °F
TEMP
123
TRUE
NOR
LOCAL
+ 9 : 00
POS
24000 P/
SPEED
V1 . 5
WP
OFF
. °F
MAG
REVS
GMT
SENS
NM
0 . 0KT
V2 . 2
SHIP
CLR
CANC
ADJ SET
SET