Icom iPW1, iPW1EURO

OPERATION

■Programming the CI-V address (continued)

DSetting the IC-PW1/EURO’s address

It is not necessary to change the IC-PW1/EURO’s

default CI-V address of 54H. However, if desired, the

address can be changed using the internal address

switch illustrated below.

It is not necessary to change the IC-PW1/EURO’s

default CI-V address (default S3=5, S4=4). However,

in the case when you will connect two (2) IC-

PW1/EUROs like as above left1, please set a differ-

ent address number using the internal address switch

as illustrated as above right.

NOTE: Turn the power OFF when you are going to

change the address setting, then programming the

CI-V address again.

ïOther NOTE:

•IC-781;

NEVER TURN THE POWER OFF of the IC-781 dur-

ing the operation when you are using the IC-781 as

one of the exciters, otherwise the CI-V control may

be interrupted.

•Baud rate;

Higher baud rate (e.g. 9600 bps) gives quick opera-

tion. When you select an extra Low baud rate (e.g.

300 bps), then the IC-PW1/EURO needs max. 15

sec. to start the operation.

•“AUTO” baud rate;

When you want to use “AUTO” baud rate, turn the

non-“AUTO” baud rate exciter ON ﬁrst, then turn the

“AUTO” baud rate exciter ON.

➥Push [POWER] to turn the linear ampliﬁer ON

then turn the exciter’s power ON.

REMOTE

Icom

exciter

IC-PW1

Icom

exciter

Address switch

‘Initial settings for CI-V remote control operation

Before setting the remote control operation, refer to

the following operating procedure.

ïïWhen using one (1) Icom exciter with one (1)

ANT line;

qTurn OFF both of the IC-PW1/EURO and exciter.

wSet [EXCITER] to [1] position.

eWhile pushing and holding the [INPUT] switch on

the IC-PW1/EURO controller, turn the exciter’s

power ON.

•LED [INPUT z] over the [INPUT] switch blinks.

rRotate the exciter’s dial until the LED [INPUT z]

lights continuously.

tTurn the exciter’s power OFF to complete the set-

ting.

ïïWhen using two (2) Icom exciters;

qTurn OFF both of the IC-PW1/EURO and exciters.

wSet [EXCITER] to [1&2] position.

eSet the exciter’s CI-V baud rate if required.

•

When selecting the different baud rate for each exciter,

“CI-V data” setting may fail depending on the exciter.

In such case, use the same baud rate for each exciter.

Each exciter’s frequencies may be synchronised.

•When connecting the “AUTO” baud rate exciter and

“Non-AUTO” baud rate exciter, the exciters’ frequen-

cies may not synchronize in some cases.

rWhile pushing and holding the [INPUT] switch on

the IC-PW1/EURO controller, turn the 1st exciter’s

power ON.

•LED [INPUT z] blinks.

☞

Continue to the next page

EXCITER

1 1&2

ANT

ACC-1

ANT1

ACC(2)

REMOTE

INPUT1

INPUT2

GND

IC-PW1/EURO

ANT1 or 2

ACC (13 pins)

REMOTE

Optional ACC cable (included in OPK-5)

Optional remote control cable (included in OPK-5)

ACC (supplied)

GND

ACC-2

OPC-599 (optional)

IC-PW1/EURO

ACC cable (supplied)

ANT ACC-1

ANT1

REMOTE

INPUT1

GND

IC-706

ACC

OPC-599 (optional)

EXCITER

1 1&2