Icom iPW1, iPW1EURO

3OPERATION

The IC-PW1/EURO uses CI-V frequency data for

automatic selection of the operating band. Program

the exciter’s address to use this capability as follows:

For non-Icom exciters, the IC-PW1/EURO cannot

be controlled using the CI-V function, so this set-

ting is not necessary.

For transceivers which have multiple antenna con-

nectors for speciﬁed bands (e.g. IC-726, IC-729,

etc.), set the same as for 2 Icom exciters.

DSetting the Icom exciters

When connecting 2 or more CI-V devices:

DO NOT use the “AUTO” baud rate for CI-V

devices. We recommend that all CI-V devices are

set to 9600 bps.

•When using the same baud rate, the exciters’ fre-

quencies are synchronized.

•When using different baud rates (i.e. 4800 and

9600 bps, etc.), the exciters’ frequencies are not

synchronized.

qConﬁrm that the exciter’s CI-V transceive function

is ON.

- Refer to the instruction manual for details.

When connecting 2 exciters, connect the 1st and

2nd exciter to [INPUT1] and [INPUT2], respectively.

eWhen connecting 2 Icom exciters, set [EXCITER]

to the [1&2] position.

rWhen connecting 2 or more CI-V devices, DO

NOT set to “AUTO” baud rate.

- Refer to the instruction manual for details.

- When using the same baud rate, the exciters’ fre-

quencies are synchronized.

- When using different baud rates (i.e. 4800 and 9600

bps, etc.), the exciters’ frequencies are not synchro-

nized. [INPUTz] and [INPUTx] selection is automat-

ically selected using the exciter’s baud rate.

•DO NOT USE

-17

V LEVEL CONVERTER

to con-

nect the remote control signal line for band control

operation from an Icom exciter, or from the PC.

•Connect the supplied remote cable between the IC-

PW1/EURO and Icom exciter directly.

DWhen using 1 Icom exciter

qWhile pushing [INPUT], push [POWER] to enter

the CI-V address programming mode.

- [INPUTz] blinks.

wRotate the Icom exciter’s tuning dial until the

[INPUTz] light continuously lights.

ePush [POWER] to turn the IC-PW1/EURO power

OFF and complete the setting.

DWhen using 2 Icom exciter’s

qWhen using 2 Icom exciters, be sure that

[EXCITER] is set to the [1&2] position.

wWhile pushing [INPUT], push [POWER] to enter

the CI-V address programming mode.

- [INPUTz] blinks.

ePush [DOWN].

- The band indicators, [1.8]–[50], light continuously.

rRotate the 1st Icom exciter’s tuning dial until the

[INPUTz] light continuously lights.

tWhen 1 Icom exciter and 1 non-Icom exciter are

connected, turn the power OFF to complete the

setting. When 2 Icom exciters are connected,

push [INPUT].

- [INPUTx] blinks when [INPUT] is pushed.

yRotate the 2nd Icom exciter’s tuning dial until the

[INPUTx] light continuously lights.

uPush [POWER] to complete the setting.

☞

Continue to the next page…

HF/50MHz ALL BAND 1kW LINEAR AMPLIFIER

iPW1

POWER

TRANSMIT

TUNER

DOWN UP

AUTO

AMP/

PROTECT

1.8 3.5 710 14 18 21 24 28 50

TEMP

ALC

SWR

METER-1 METER-2

ANT

INPUT