Installation

Electrical Requirements

GB For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than

130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing. Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

Important

It is essential that the lower cupboard is constructed in the manner illustrated i.e. having side, back, and roof panels so joined as to provide no apertures which could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2. Ventilation

a.The oven housing unit cabinet dimensions must comply with fig. 4.

b.An air gap of 50mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c.It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabinetry. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d.The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e.If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3. Final Installation

a.Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b.Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

c.Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d.The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home.

e.Finally, the oven is secured to the cabinet by means of the four Phillips C/SK Head screws - two through each side trim.

f.Remove all packaging material from the grill and oven interior.

List of loose items:

4 x Phillips C/SK Head No. 6 x 25mm screws.

22

Page 21 Page 23
Page 22
Image 22
Indesit BD32B/2, DY46X/2, DY46K/2, DH53K, BD42SS/2, BD32P/2, DH53B, DHS53X, DH53W, DH53 CK, DH53X, DY46W/2, BD32K/2 manual Installation
Page 21 Page 23

DHS53CX, BD32K/2, DY46W/2, DH53X, DH53 CK specifications

Indesit, a leading brand in household appliances, offers a variety of high-quality dryers that cater to diverse needs. Among these models, the Indesit DY46X/2, DY46K/2, DH53K, BD42SS/2, and BD32P/2 stand out for their performance, technology, and user-friendly features.

The Indesit DY46X/2 is designed to make laundry days a breeze. Boasting a large drum capacity of 8 kg, it allows users to dry more clothes in one cycle, saving time and energy. This model incorporates sensor drying technology, which adjusts the drying time based on the moisture level of the clothes, preventing over-drying and promoting fabric care. Its multiple drying programs accommodate various fabric types, ensuring optimal results for every load.

The DY46K/2 model offers similar functionality with an energy efficiency rating that helps in reducing power consumption. Its wide range of drying options caters to delicate items as well as heavier fabrics. With a simple control panel, users can easily navigate through programs and select the appropriate settings for their laundry, making it convenient for busy households.

Moving on to the DH53K, this model features a unique reverse action technology that helps to prevent clothing from clumping together during tumbling. This innovative feature ensures even drying and reduces creasing, making ironing less of a chore. The DH53K also includes a wool drying program, specially designed to take care of delicate wool garments, and maintain their quality over time.

For those looking for a stylish appliance, the BD42SS/2 and BD32P/2 deliver both aesthetics and performance. The BD42SS/2 features a stainless-steel finish that adds a modern touch to any laundry room while providing durable and reliable service. Its large 9 kg capacity makes it perfect for families, while its energy efficiency rating helps keep operational costs down.

The BD32P/2, on the other hand, caters to smaller households with its compact design and 7 kg capacity. Despite its size, it doesn't compromise on features, offering a variety of drying programs and a user-friendly digital interface. This model is an ideal choice for those with limited space but without sacrificing performance.

In summary, the Indesit DY46X/2, DY46K/2, DH53K, BD42SS/2, and BD32P/2 models showcase a blend of advanced technologies, efficiency, and user comfort. With options for various needs and preferences, Indesit continues to provide reliable solutions in the world of laundry appliances.
Top Page Image Contents