Connecting the gas supply, Electrial connection

HOT PARTS

Important: make sure the supply pressure conforms with the values shown in the table entitled “Caracteristics of the burners and nozzles”. When the cooker is installed between cabinets (recessed), the gas connection must be effected by an approved flexible hose with bayonet fitting (BS 669 Current Edition).The gas inlet for the cookers is a threaded G 1/2 gas female fitting.

Connecting the gas supply

To make the connection, a flexible hose should be used corresponding to the current gas regulations which are:

•the hose must never be at any point in its lenght in contact with the “hot” parts of the cooker;

•the hose must never be longer than 1,5 metre;

•the hose must not be subject to any tension or torsional stress and it must not have any excessively narrow curves or bottlenecks;

•the hose must be easy to inspect along its entire length to check its condition;

•the hose must always be in good condition, never attempt to repair.

Important: the installation must comply with gas safety (installation and use) regulations 1984.In all cases for the above, by low, a qualified, corgi approved engineer must be called for installation.

Electrial connection

Power supply voltage and frequency: 230-240V a.c. 50 Hz.

Note: the supply cable must be positioned so that it never reaches at any point a temperature 50°C higher than the room temperature.The cable must be routed away from the rear vents. Should you require it, you may use a longer cable, however, you must ensure that the cable supplied with the appliance is replaced by one of the same specifications in accordance with current standards and legislation.

Your appliance is supplied with a 13 amp fused plug that can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING -THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug.Replacements can be obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and you should wish to remove it to add a cable extension or to re-route the mains cable through partitions, units etc., please ensure that either:

•the plug is replaced by a fused 13 amp re-wireable plug bearing the BSI mark of approval.

or:

•the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance.

Please note: for appliances with a rating greater than 13 amp

(eg:electric hob, double ovens and freestanding electric cookers etc.) the mains cable must be wired into a cooker output point with a rating of 45 amp. In this case the cable is not supplied.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket. Instructions for connecting cable to an alternative plug: Important: the wires in the mains lead are coloured in accordance with the following code:

Green &Yellow	- Earth
Blue	- Neutral
Brown	- Live

If the colours of the wires in the mains lead do not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked “E” or					or

coloured Green or Green &Yellow.

Connect Brown wire to terminal marked “L” or coloured Red. Connect Blue wire to terminal marked “N” or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse. A 15 amp plug must be protected by a 15 amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt about the electrical supply to your machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance with

the following code:
BLUE			“NEUTRAL”(“N”)
BROWN			“LIVE”(“L”)
GREEN ANDYELLOW			“EARTH” (“E”)

	GREEN &
	YELLOW
	BROWN	13 amp fuse
	BROWN
	BLUE	CROSS-BAR
		CORD GRIP

Disposing of the appliance

When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.

Adapting the cooker to different types of gas

In order to adapt the cooker to a different type of gas with respect to the gas for which it was produced (indicated on

K 642 V/G, K 642 VS/G specifications

Indesit K 642 VS/G and K 642 V/G are two highly sought-after models in the world of gas cookers, known for their reliability and performance. These cookers embody a blend of practicality and modern design, making them a perfect addition to any kitchen.

One of the main features of the Indesit K 642 VS/G and K 642 V/G models is their four gas burners, which offer various cooking options to suit different culinary needs. The burners come in different sizes, allowing users to select the ideal flame for their pots and pans. This feature enhances cooking efficiency, enabling rapid boiling, simmering, and frying.

Another appealing characteristic is the enamelled surface of the cooktops. This not only adds a sleek look to the kitchen but also ensures easy cleaning. The smooth surface allows for quick wipe-downs and maintenance, vital for those with a busy lifestyle or who enjoy cooking regularly.

The integrated ignition system is another essential technology present in these models. With a simple push and turn of the knobs, users can ignite the burners without needing matches or a lighter, adding convenience and safety to the cooking experience. Additionally, the safety features include a flame failure device that automatically shuts off the gas supply if a flame goes out, preventing potential hazards.

Both models also feature an oven with a generous capacity, ideal for baking, roasting, and grilling. The oven boasts various functions to support diverse cooking methods, including a traditional static mode for baking and a grill option for finishing off dishes. The stylish glass door allows users to monitor their dishes without opening the oven, thus retaining heat.

Moreover, the K 642 series is designed with energy efficiency in mind. The ovens are designed to provide optimal heat distribution ensuring food cooks evenly while also conserving energy. This makes the models not only cost-effective in terms of energy bills but also environmentally friendly.

In summary, the Indesit K 642 VS/G and K 642 V/G models are practical, efficient, and stylish gas cookers ideal for any modern kitchen. With their user-friendly features, robust safety mechanisms, and versatile cooking options, they stand out as excellent choices for both novice cooks and culinary enthusiasts alike.

Indesit K 642 V/G, K 642 VS/G Connecting the gas supply, Electrial connection, Replacing the fuse

Models: K 642 V/G K 642 VS/G