Troubleshooting

Your washing machine could fail to work. Before calling for Assistance (see page 16), make sure the problem can’t easily be

 

GB

solved by consulting the following list.

 

 

 

Problem

The machine does not switch on.

The wash cycle does not start.

The machine does not fill with water.

The machine continuously fills with water and continually drains away or Water left in the dru or Stuck on wash.

The machine does not drain or spin.

The machine does not heat or poor wash results.

The programme takes too long.

The machine vibrates a lot during the spin cycle.

Possible causes/Solution:

•The appliance is not plugged into the socket fully, or not enough to make contact.

•There is no power to the socket, or the fuse has blown in the mains plug.

•The door is not closed properly.

•The ‘ON/OFF’ button has not been pressed.

•The ‘START/RESET’ button has not been pressed.

•The water tap has not been turned on to allow water to flow into the machine.

•A delayed start has been set.

•The water inlet hose is kinked.

•The water inlet hose is not connected to the water supply.

•The water pressure is too low.

•The water tap has not been turned on to allow water to flow into the machine.

•There is no water supply to the house.

•The inlet valve filter is blocked.

•The ‘START/RESET’ button has not been pressed.

•The top of the drain hose is too low - It must be fitted at a height between 65 and 100 cm from the floor.

•The drain hose is connected incorrectly to the sink trap allowing water to run into the machine, the drain hose must be positioned higher than the bottom of the sink to prevent water flowing down the drain hose.

•The end of the drain hose has been pushed too far down the standpipe, the ‘U’ bracket should be fitted 100 mm from the end of the drain hose.

•The Pump filter is blocked.

•The “Easy iron” function is enabled: to complete the programme, press the START/RESET button (see page 13).

•The drain hose is kinked.

•New Installation - The blanking cap or spigot has not been removed if connected under a sink.

•The drain hose or sink trap is blocked.

•The wash cycle does not include draining, some wash cycles require the drain phase to be started manually.

•The ‘Spin Speed’ selector knob is in the position.

•The ‘Temperature’ selector knob is in the position.

•Programme times will vary due to water pressure, the incoming water temperature and if the wash load goes out of balance. This will increase the programme times accordingly (see ‘ The machine wont spin properly’ below).

•The feet have not been adjusted, enabling the machine to rock.

•New Installation - Either the Transit Bolts including the plastic spacers, or the Polystyrene Packaging have not been removed when installing the machine.

•The machine is trapped between cabinets and/or walls.

•The load is in a slight out of balance condition and machine is spinning, but at a lower speed.

15

Page 14 Page 16
Page 15
Image 15
Indesit WME 126 manual Troubleshooting, Problem, Possible causes/Solution, Solved by consulting the following list
Page 14 Page 16

WME 126 specifications

The Indesit WME 126 is a versatile and efficient washing machine designed to meet the needs of modern households. This front-loading appliance combines performance, functionality, and energy efficiency, making it a popular choice for families and individuals alike.

One of the standout features of the Indesit WME 126 is its impressive washing capacity. With a load capacity of up to 6 kg, this machine allows users to wash larger loads in a single cycle, saving time and energy. This is especially beneficial for busy households that require frequent laundry loads.

The Indesit WME 126 is equipped with a range of wash programs, designed to cater to different fabric types and levels of dirt. These programs include cotton, synthetics, delicates, and even a rapid wash cycle that can clean lightly soiled items in just 30 minutes. This feature is particularly useful for those on the go who need clean clothes in a hurry.

In terms of energy efficiency, the Indesit WME 126 boasts an A+ energy rating, highlighting its ability to reduce energy consumption without compromising on performance. This ensures not only lower utility bills but also a reduced environmental footprint, making it an eco-friendly option for consumers.

The machine utilizes innovative technologies to enhance the washing experience. One such feature is the variable temperature control, which allows users to adjust the water temperature according to the fabric type and level of soiling. Additionally, the adjustable spin speed can be customized up to 1200 RPM, providing users with the ability to tailor the washing cycle to their specific needs.

Another notable characteristic of the Indesit WME 126 is its user-friendly interface. The simple dial and button controls make it easy to select the desired wash program and configure settings, ensuring a hassle-free experience. The machine also includes a delay timer, allowing users to set their wash cycle to start at a more convenient time.

Durability and reliability are key attributes of the Indesit WME 126, built to withstand regular use while maintaining optimal performance. With a modern design, this washing machine fits seamlessly into any laundry room or kitchen aesthetic.

Overall, the Indesit WME 126 stands out as a practical and effective washing machine, making it an excellent investment for anyone seeking a dependable laundry solution. With a combination of essential features and efficient technologies, it meets the diverse washing needs of everyday life.
Top Page Image Contents