PROVENAIR SEAL KITS
RKN 
X 
X 
X 
X 
B
CYLINDER TYPE
A- Double Acting, Single Rod End
B- Double Acting, Double Rod End
BORE SIZE |
|
|
|
| |
|
|
|
| ||
Q | - | 5 | - 5” | ||
S | - 2” | 6 | - 6” | ||
T | - | 8 | - 8” |
| |
W - | Y | - 10” | |||
4 | - 4” | NOTE: All seal kits include wear strip and cushion seals. | |||
|
| ||||
CUSHIONED BOTH ENDS SEALS
B - Nitrile; Nitrile, Mag
S-
ROD DIAMETER
K | - 5/8” | Q | - |
M | - 1” | S | - 2” |
P | - |
|
|
HEADS AND CAPS
CYLINDER | 2” BORE | 4” BORE | |||||||||||||
TYPE | HEAD |
| CAP | HEAD |
| CAP | HEAD |
| CAP | HEAD |
| CAP | HEAD |
| CAP |
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
119462 |
| 119471 | 119480 |
| 119489 | 119498 |
| 119507 | 119516 |
| 119525 | 119534 |
| 119543 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CUSHIONED | 119651 |
| 119666 | 119654 |
| 119669 | 119657 |
| 119672 | 119660 |
| 119675 | 119663 |
| 119678 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
119464 |
| 119473 | 119482 |
| 119491 | 119500 |
| 119509 | 119518 |
| 119527 | 119536 |
| 119545 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CUSHIONED MS4 | 119652 |
| 119667 | 119655 |
| 119670 | 119658 |
| 119673 | 119661 |
| 119676 | 119664 |
| 119679 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
119901 |
| 119902 | 119903 |
| 119904 | 119905 |
| 119906 | 119907 |
| 119908 | 119909 |
| 119910 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CUSHIONED TRUNNION | 119653 |
| 119668 | 119656 |
| 119671 | 119659 |
| 119674 | 119662 |
| 119677 | 119665 |
| 119680 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 119752 |
| 119754 | 119756 |
| 119758 | 119760 |
| 119762 | 119764 |
| 119766 | 119768 |
| 119770 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CUSHIONED FEM. RET. BOLT | 114063 |
| 114064 | 114065 |
| 114066 | 114067 |
| 114068 | 114069 |
| 114070 | 114071 |
| 114072 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 119835 |
| 119836 | 119839 |
| 119840 | 119843 |
| 119844 | 119847 |
| 119848 | 119851 |
| 119852 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 119877 |
| 119878 | 119879 |
| 119880 | 119881 |
| 119882 | 119883 |
| 119884 | 119885 |
| 119886 |
119577-( ) SPACER INSTALLATION
To replace tie rod cylinders that have end caps made from castings (such as Wabco, Taiyo and Aro series 38 / 39), use | |||
spacers as called out below. |
|
| MF1 Head Flange |
| Q Spacer |
| |
|
| Mounting Screw for MF1 mount (4 req’d) g | |
| Cylinder Head |
| |
|
|
| |
|
|
| |
“B”
“B”
“A”
gNot Supplied
BORE | SPACER | “A” | “B” | CAP SCREW g | TORQUE |
SIZE |
|
|
|
| (FT LBS) |
.375” | 2.000” | 1/4” - 28 x | 9 | ||
|
|
|
|
|
|
2” | .375” | 2.500” | 5/16” - 24 x | 16 | |
|
|
|
|
|
|
.375” | 3.000” | 5/16” - 24 x | 21 | ||
|
|
|
|
|
|
.625” | 3.750” | 3/8” - 24 x | 35 | ||
|
|
|
|
|
|
4” | .625” | 4.500” | 3/8” - 24 x | 49 |
QWhen used with MF1 flange, spacer 119577-( ) is mounted between head and flange and requires 4 mounting screws of the size listed in the table.
QWhen used without MF1 flange, spacer 119577-( ) is slid over piston rod and bushing, against cylinder head. No new mount- ing screws are required. Spacer is attached using Loctite or “superglue”.
